Wayne-Dalton 2411 Benutzerhandbuch
3” TRACK 1/4” GRADUATION
9 SECTIONS HIGH OR LESS
FIG.F
FIG.I
FIG.H
FIG.G
Align the appropriate end hinge to the pre-punched holes in the stiles and secure using (2) 1/4” x 5/8”
self tapping screws per hinge. Products 16’2” wide and less require (1) end hinge (fig. D) and doors over
16’2” wide require double end hinges. (Fig. H)
The end hinge sequence is dependent on track size (2” or 3”).
2” track applications begin with a number 1 hinge attached to the top corners of the bottom section.
3” track applications begin with a number 3 hinge.
self tapping screws per hinge. Products 16’2” wide and less require (1) end hinge (fig. D) and doors over
16’2” wide require double end hinges. (Fig. H)
The end hinge sequence is dependent on track size (2” or 3”).
2” track applications begin with a number 1 hinge attached to the top corners of the bottom section.
3” track applications begin with a number 3 hinge.
( Refer to the illustrations dependant on your track size)
#3 HINGE
#4 HINGE
#5 HINGE
PG. 5
FIG.J
Refer to the auxiliary
instructions.
Secure Bracket
using (10) screws.
NOTE:
3” TRACK HINGE SCHEDULE ON
DOORS LESS THAN OR EQUAL TO 18’-1” HIGH.
DOORS OVER 18’-1” HIGH (OVER 9 SECTIONS)
WILL REQUIRE 1/8” GRADUATION. BY START-
ING WITH (2) #3 HINGES, (2) #4 HINGES, (2) #5
HINGES ETC...
DOORS OVER 18’-1” HIGH (OVER 9 SECTIONS)
WILL REQUIRE 1/8” GRADUATION. BY START-
ING WITH (2) #3 HINGES, (2) #4 HINGES, (2) #5
HINGES ETC...
NOTE:
DOUBLE END-
STILES BEGIN AT 16’3” WIDE
ON ALL 2411-2415 DOORS
ON ALL 2411-2415 DOORS
WARNING: DO NOT USE UNDERSIZED WINDING RODS (SCREWDRIVERS, ETC.)
Wind springs 1/4 turn at a time to the number of complete
revolutions recommended on the spring tag. Wind up as
shown Fig. When the proper number of turns is reached,
rest the winding rod against the top section or header,
stretch the spring then, tighten the set screws on the
winding cone. Release the vice grips from the spring
shaft(s). Adjust the coupler on split solid shafts until
drums are in time (check door level) and tighten coupler.
revolutions recommended on the spring tag. Wind up as
shown Fig. When the proper number of turns is reached,
rest the winding rod against the top section or header,
stretch the spring then, tighten the set screws on the
winding cone. Release the vice grips from the spring
shaft(s). Adjust the coupler on split solid shafts until
drums are in time (check door level) and tighten coupler.
WARNING: Apply locking pliers to the track ABOVE the
roller and lock door if applicable, before winding the spring
roller and lock door if applicable, before winding the spring
Wind springs toward ceiling.
(Standard lift applications)
(Standard lift applications)
SPRING TURN CHART
PG. 12
DOOR HEIGHT
400-8
400-12
5250-18
800-32
6'6"
7 1/2
7 1/2
7'0"
7 7/8
7 7/8
7'6"
8 1/2
8 1/2
8'0"
8 7/8
8 7/8
6 3/4
8'6"
9 1/4
7 1/8
9'0"
9 1/2
7 3/8
9'6"
10 1/8
7 3/4
10'0"
10 1/2
8 1/8
5 3/8
10'6"
11
8 3/8
5 5/8
11'0"
11 1/2
8 7/8
5 7/8
11'6"
12
9 1/8
6
12'0"
12 1/2
9 1/2
6 1/4
12'6"
9 7/8
6 1/2
13'0"
10 1/4
6 3/4
13'6"
10 1/2
7
14'0"
10 7/8
7 3/8
DOOR HEIGHT
400-8
400-12
5250-18
800-32
14'6"
11 1/4
7 1/2
15'0"
11 1/2
7 5/8
15'6"
11 7/8
8
16'0"
12 1/4
8 1/8
16'6"
12 1/2
8 1/4
17'0"
12 7/8
8 5/8
17'6"
13 1/4
8 7/8
18'0"
13 1/2
9
18'6"
9 1/4
19'0"
9 1/2
19'6"
9 3/4
20'0"
9 7/8
20'6"
10 1/4
21'0"
10 3/8
21'6"
10 1/2
22'0"
11