Skylink Model UR-100 Merkblatt

1. Locate frequency switch

on the top of the trans-
mitter and set to position
A. (See diagram N)

2. To program the model

#68, #68C, #68B, #68G,
#68R, open the case
with a coin. (See dia-
gram O)

Diagram N

Diagram O

4.  Use an opened paper clip to set the connectors numbered

1 through 9 so that the switches on the transmitter match
those on the receiver. To operate with Skylink #UR100, only
set to “ + ” or “ 0 ” position. Do not place the connector to
the middle & bottom posts “ - ” position. Leave the remaining
posts at “ 0 ”, or the blank position (remove the connectors).
See the Diagram J for details.

3. The transmitter has 12 rows

of posts, each row has 3
posts. (see diagram P)

Diagram P

5. Test the transmitter with the Universal receiver.

6. To move the connectors, slide an

opened paper clip into the side of
a connector and lift. (see diagram
M) When repositioning connec-
tors, place a connector on the two
chosen posts, then push down on
the connector with your finger.

Diagram M

7. Set the connectors num-

bered 1 through 9 so that
the switches on the trans-
mitter match those on the
receiver. Leave the re-
maining posts at “ 0 ”,or
the blank position (remove
the connectors). See the
diagram J for details.

8. Test the transmitter with

the Universal receiver.

1. To Program Your Keypad

- Open the cover on the
  back. (See diagram Q)

2. Set brand jumper by moving the red plastic

tab to the number 7 jumper. Slide an opened
paper clip into the
top of the red plastic
tab, then lift and re-
position.

Frequency
Switch

DIP Switch Location

1 2

3

4

5

6

7

8

Brand Jumper

3.  Set the frequency

switch located above
to “ D ” position (slide
the switch as far
right as possible).
(See diagram R)

5.  Refer to the keypad manual

to test the transmitter with
the Universal receiver.

1. To Program Your Keypad

- Open the cover on the
  back. (See diagram T)

Frequency
Switch

Brand Jumper

Diagram W

Diagram V

Diagram Q

Diagram T

Diagram R

Diagram S

Diagram U

1 2

3

4

5

6

7

8

The Universal Garage Door
Remote Control is approved
by the FCC and it complies
with Part 15 of the FCC
Rules. Its operation is
subject to the following two
conditions :
1.  This device may not

cause harmful inter-
ference.

2.  This device must accept

any interference that
may cause undesired
operation.

Skylink will not be held liable
or responsible for
any misuse or application
of this product other than
for its intended use.

USER'S INSTRUCTIONS

® are registered  trademarks of their respective corporations

2213 Dunwin Drive,
Mississauga, Ontario
L5L 1X1, CANADA
(905)608-9223
(905)608-8744 FAX
Email:support@skylinkhome.com
           (Reply within 24 hrs)
Customer Service : (800)304-1187
http://www.skylinkhome.com
P/N. 101A111-003  Rev.3
Patent no. 382251
Patents Pending
©1999 SKYLINK TECHNOLOGIES INC.

WARNING:
Changes or modifications
to this unit not expressly
approved by the party res-
ponsible of compliance
could void the user’s
authority to operate the
equipment.

DO NOT let children
use any garage door
transmitter without
adult supervision.
Children can injure
themselves or others
by the garage door.

If, within one year from date
of purchase, this product
should become defective
(except battery), due to
faulty workmanship or
materials, it will be repaired
or replaced, without charge.
Proof of purchase is
required.

®

4. Use a pen or paper clip

to set the corresponding
DIP switches numbered
1 through 9 so that the
switches on the trans-
mitter match those on
the receiver. Each switch
of the transmitter has 3
positions (“ + ”, “ 0 ”,
“ - ”). To operate with
Skylink #UR-100, only
set the switches to “ + ”
or “ 0 ”. Do not use “ - ”
position. Leave the re-
maining DIP switches in

the transmitter at “0” or
the center position. (See
diagram S)

5. Refer to the keypad manual to test the transmitter with the Universal

receiver.

4.  The connector (See diagram V) has 12 rows of posts, each row

has 3 posts. Each row contains one connector (See diagram
W). Set the code connectors from number 1 through 9 so that
the switches on the transmitter match those on the receiver.
To operate with #UR100, only set the connectors to “ + ” or “0”
(blank position). Do not set the connectors to “ - ” position. Leave
the remaining posts at “ 0 ”, or the blank position (remove the
connectors). See the diagram L for details.

2. Set brand jumper by moving the red plastic

tab to the number 7 jumper. Slide an opened
paper clip into the
top of the red plastic
tab, then lift and re-
position.

3.  Set the frequency

switch located above
to “ D ” position
(slide the switch
as far right as
possible). (See
diagram U)

Code connector Location