Vermont Casting LHEC30 Benutzerhandbuch

3

10005360

Vermont Castings, Majestic Products LHE Natural Vent Insert

This gas appliance should be installed by a qualified installer
in accordance with local building codes and with current CSA-
B149.1 Installation codes for Gas Burning Appliances and
Equipment.

FOR U.S. Installations follow local codes and/or the current
National Fuel Gas Code ANSI Z223.1.

FOR SAFE INSTALLATION AND OPERATION OF
YOUR GAS FIREPLACE PLEASE NOTE THE
FOLLOWING:

1. This appliance gives off high temperatures and should be

located out of high traffic areas and away from furniture
and draperies.

2. Children and adults should be alerted to the hazards of the

high surface temperatures of this appliance and should
stay away to avoid burns or ignition of clothing.

3. Children should be carefully supervised when they are in

the same room as your appliance.

4. Under no circumstances should this appliance be modified.

Parts removed for servicing should be replaced prior to
operating this appliance again.

5. Installation and any repairs to this appliance should be

carried out by a qualified service person. A professional
service person should be contacted to inspect this appli-
ance annually. Make it a practice to have all of your gas
appliances checked annually.  More frequent cleaning may
be required due to excess lint and dust from carpeting,
bedding material, etc.

6. Control compartments, burners and air passages in this

appliance should be kept clean and free of dust and lint.
Make sure that the gas valve and pilot light are turned off
before you attempt to clean this unit.

7. The venting system (chimney) of this appliance should be

checked at least once a year and if needed your venting
system should be cleaned.

8. Keep the area around your appliance clear of combustible

materials, gasoline and other flammable vapor and liquids.
This appliance should not be used as a drying rack for
clothing, nor should Christmas stockings or decorations be
hung in the area of it.

9. Under no circumstances should any solid fuels (wood, coal,

paper or cardboard etc.) be used in this appliance.

10. Whether the zero clearance kit is installed directly on

carpeting, vinyl tile or any combustible material other than
wood, this heater must be installed on a metal or wood
panel extending the full width and depth of the heater. The
insert can not be installed directly onto  or into
combustibles.

It is normal for fireplaces fabricated of steel to give off
some expansion and/or contraction noises during the
start up or cool down cycle.  Similar noises are found
with your furnace heat  exchanger or car engine.

It is not unusual for your Vermont Castings, Majestic
Products gas fireplace to give off some odor the first
time it is burned.  This is due to the curing of the paint
and any undetected oil from the manufacturing process.

It is recommended that you burn your Vermont
Castings, Majestic Products fireplace for at least ten
(10) hours the first time you use it.  If optional fan kit has
been installed, place fan in the "OFF" position during
this time.

Proposition 65 Warning: Fuels used in gas,
woodburning or oil fired appliances, and the products
of combustion of such fuels, contain chemicals known
to the State of California to cause cancer, birth defects
and other reproductive harm.
California Health & Safety Code Sec. 25249.6

FP1249

Fig. 1  Locating unit with zero clearance kit.

A)

Flat on wall

B)

Cross corner

C)  Island

D)

*Room divider

E)

*Flat on wall corner

F)

Chase installation

NOTE: (Fig. 1)
*  When you install your Vermont Castings, Majestic Products
fireplace in (D) Room divider or (E) Flat on wall corner positions,
a minimum of 6 (X) inches (153mm) clearance must be main-
tained from the perpendicular wall and the outer edge of the trim.

Before installing the gas fireplace insert, consideration
must be given to the functioning needs of the fireplace.
The size of the fireplace cavity (min. 25

¹⁄₄

"W x  17

¹⁄₄

"H x

13

¹⁄₂

" D for the LHEC20 and LHER20, 28

³⁄₄

"W x 21"H x

15

¹⁄₂

"D for LHEC30 ), the design of the chimney for

effective venting should be determined. The availability of
the gas supply as well as electricity for the insert fan
must be confirmed.

This appliance may be installed in an aftermarket
permanently located, manufactured (mobile) home,
where not prohibited by local codes.

This appliance is only for use with the type of gas
indicated on the rating plate.