Hearth & Home Technologies 8300 Benutzerhandbuch
HearthStone Quality Home Heating Products Inc
Champlain
Model #8300
8
O
WNER
’
S
I
NFORMATION
The installation must conform with local
codes or, in the absences of local codes, the
current National Fuel Gas Code, ANSI Z223.1
(NFPA 54) or CAN/CGA B149 Installation
Code. (Installer l’appareil selon les codes ou
règlements locaux, ou, en l’absence de tels
règlements, selon les Codes d’installation
CAN/CGA-B149.)Do not use this appliance
if any part has been under water.
Immediately call a qualified service
technician to inspect the heater and to
replace any part of the control system and
gas control that has been under water. (Ne
pas se servir de cet appareil s’il a été plongé
dans l’eau, complètement ou en partie.
Appeler un technicien qualifié pour inspector
l’appareil et remplacer toute partie du système
de contrôle et toute commande qui ont été
plongés dans l’lau.
codes or, in the absences of local codes, the
current National Fuel Gas Code, ANSI Z223.1
(NFPA 54) or CAN/CGA B149 Installation
Code. (Installer l’appareil selon les codes ou
règlements locaux, ou, en l’absence de tels
règlements, selon les Codes d’installation
CAN/CGA-B149.)Do not use this appliance
if any part has been under water.
Immediately call a qualified service
technician to inspect the heater and to
replace any part of the control system and
gas control that has been under water. (Ne
pas se servir de cet appareil s’il a été plongé
dans l’eau, complètement ou en partie.
Appeler un technicien qualifié pour inspector
l’appareil et remplacer toute partie du système
de contrôle et toute commande qui ont été
plongés dans l’lau.
L
IGHTING
I
NSTRUCTIONS
NOTE:
The gas control knobs and the piezo
ignitor are located behind the control valve
access door, under the front of the unit.
1. STOP! Read the What To Do If You
access door, under the front of the unit.
1. STOP! Read the What To Do If You
Smell Gas! Warning (on the cover of
this manual).
this manual).
2. Set the on/off/T-stat switch or thermostat
to the “OFF” position.
3. Push in and turn gas control knob
to the “OFF” position.
3. Push in and turn gas control knob
clockwise to “OFF”. (If not previously
lit, the knob should be in this position.)
lit, the knob should be in this position.)
4. Wait (5) five minutes to clear out any
gas. If you then smell gas, STOP! Smell
all around the appliance area for gas.
Be sure to smell next to the floor because
some gases are heavier than air and will
settle on the floor. If you smell gas
immediately follow the What To Do If
You Smell Gas! warning on the cover of
this Manual. If you do not smell gas,
proceed to the next step.
all around the appliance area for gas.
Be sure to smell next to the floor because
some gases are heavier than air and will
settle on the floor. If you smell gas
immediately follow the What To Do If
You Smell Gas! warning on the cover of
this Manual. If you do not smell gas,
proceed to the next step.
5. Turn gas control knob counter-clockwise
to “PILOT”.
6. Push in control knob all the way and
hold in. Immediately light the pilot with
the gas lighter (push in and “click” the
piezoelectric spark ignitor button several
times until lit). Continue to hold the
control knob in for about 20 seconds
after the pilot is lit. Release the knob and
it will pop back out. Pilot should remain
lit. If the pilot goes out, repeat the
operation.
the gas lighter (push in and “click” the
piezoelectric spark ignitor button several
times until lit). Continue to hold the
control knob in for about 20 seconds
after the pilot is lit. Release the knob and
it will pop back out. Pilot should remain
lit. If the pilot goes out, repeat the
operation.
•
If knob does not pop out when released,
stop, shut off the gas supply to the heater
and immediately call a qualified service
technician or gas supplier.
stop, shut off the gas supply to the heater
and immediately call a qualified service
technician or gas supplier.
•
If the pilot will not stay lit after several
tries, turn the gas control knob “OFF”
and call a qualified service technician or
gas supplier.
tries, turn the gas control knob “OFF”
and call a qualified service technician or
gas supplier.
7. After the pilot lights, turn gas control
knob counter-clockwise to “ON”.
8.
If the ON/OFF/THERMOSTAT switch
is set to “ON”, the stove should now be
lit. If the thermostat (or remote) has been
installed, set the ON/OFF
THERMOSTAT switch
is set to “ON”, the stove should now be
lit. If the thermostat (or remote) has been
installed, set the ON/OFF
THERMOSTAT switch
to
“THERMOSTAT” and turn the
thermostat (or remote) to “ON”. Then
set the desired temperature.
thermostat (or remote) to “ON”. Then
set the desired temperature.
9. Shut the gas control valve access door.
NOTE
:
When pressing/clicking the
piezoelectric spark ignition button to light
the pilot, watch through the glass (front) of
the unit. Click the ignitor button until a
flame is visible at the pilot. Once the pilot is
lit, continue to press on the gas control knob
for another 20 seconds, then release.
Ascertain that the pilot is still lit by looking
through the front door. If lit, then turn the
gas control knob fully counter-clockwise to
the pilot, watch through the glass (front) of
the unit. Click the ignitor button until a
flame is visible at the pilot. Once the pilot is
lit, continue to press on the gas control knob
for another 20 seconds, then release.
Ascertain that the pilot is still lit by looking
through the front door. If lit, then turn the
gas control knob fully counter-clockwise to