Regency F37-NG Benutzerhandbuch
22
F37 Regency
®
Rear Flued Room Sealed Freestanding Gas Heater
MAINTENANCE
REMOVING VALVE
If your valve requires maintenance or replace-
ment, use the following instructions:
ment, use the following instructions:
Note: Always close off the gas supply before
removing the valve.
1) Open front pedestal door. You may want to
put a soft cloth on the base of the unit so that
when the pedestal door is open it doesn't
scratch the paint. See diagram below.
when the pedestal door is open it doesn't
scratch the paint. See diagram below.
FAN MAINTENANCE
If your fan requires maintenance or replacement
it must be performed by an authorised person.
Access to the fan is through the plate on the rear
wall of the fi rebox. NOTE: the unit MUST NOT
be operated without the fan access panel
securely in place and correctly sealed.
it must be performed by an authorised person.
Access to the fan is through the plate on the rear
wall of the fi rebox. NOTE: the unit MUST NOT
be operated without the fan access panel
securely in place and correctly sealed.
IMPORTANT: These fans collect a
lot of dust from within your home.
Ensure you maintain these fan mo-
tors on a regular basis by vacuuming
out the fan squirrel cages, around
the motor, and around the grills on
the back of the stove.
lot of dust from within your home.
Ensure you maintain these fan mo-
tors on a regular basis by vacuuming
out the fan squirrel cages, around
the motor, and around the grills on
the back of the stove.
To remove fan:
1) Unplug or disconnect power source to
stove.
2) Remove the rear
access panel on
the back of the
stove. The fan can
only be accessed
from the back of
the stove.
the back of the
stove. The fan can
only be accessed
from the back of
the stove.
IMPORTANT
Disconnect power supply
before servicing
WARNING:
Electrical Grounding Instructions
This appliance is equipped with
a three pronged (grounding) plug
for your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle. Do not cut
or remove the grounding prong
from this plug.
Electrical Grounding Instructions
This appliance is equipped with
a three pronged (grounding) plug
for your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle. Do not cut
or remove the grounding prong
from this plug.
3) Unclip the black and white wires from the
fan motor.
4) Lift fan off of the 2 pins, tip back and pull
through the opening. Disconnect the green
ground wire from the right side of the fan as
soon as you can reach it.
ground wire from the right side of the fan as
soon as you can reach it.
Replacing Fan:
Reverse the above steps (1 - 4). Make sure the
fan wires and the ground wire are reattached.
fan wires and the ground wire are reattached.
Hint for pushing fan down onto pins - rub a bit of
dish soap on the grommet so it will slide more
easily onto the pin. Check to make sure the fan
is seated properly on the pins - try to move the
fan back and forth, there should be no noise, if
there is check that the grommets haven't come
loose.
dish soap on the grommet so it will slide more
easily onto the pin. Check to make sure the fan
is seated properly on the pins - try to move the
fan back and forth, there should be no noise, if
there is check that the grommets haven't come
loose.
2) Undo the six screws holding the control panel
in place.
3) Disconnect all wires from the back of the con-
trol panel and then remove panel. You should
lay the panel on a soft cloth so it doesn't get
marked up. See diagram above.
lay the panel on a soft cloth so it doesn't get
marked up. See diagram above.