Honeywell T7350 Benutzerhandbuch

63-2605—5

16

3. Press up S or down T until the desired time is 

displayed.

4. Press Run Schedule.

Use the PDA or almost exclusively keys in the “Schedule” 

area of the keypad for this procedure:

1. Press Occupied.

2. Press Day to select the day to be copied.

3. Press Copy.

4. Press Copy again. The following day is automatically 

selected. (For example: If the day to be copied is Mon-

day, Tuesday will automatically be selected.)

5. If necessary, press Day until the day to receive the copy 

is displayed.

NOTE: To cancel the copy press Run Schedule before 

6. Press Copy.

NOTE: DONE displays for two seconds then the 

program display reappears.

7. Repeat steps 2 through 6 for all the days desired.

8. Press Run Schedule.

1. Press Occupied or Not Occupied until the start period to 

be cleared is displayed.

2. Press Day until desired day is displayed.

3. Press Clear Start Time.

4. Repeat steps 1 through 3 for all the start times to be 

cleared.

5. Press Run Schedule.

The setpoint temperature range is 40°F to 90°F (4°C to 32°C) 

for heating and 45°F to 99°F (7°C to 37°C) for cooling.

NOTES: The ranges mentioned can be limited based upon 

setpoints and stops:

1.

The greater of the Minimum Heat Stop and the 

Not Occupied Heat setpoints determines the 

lowest setting to which the occupied heat setpoint 

can be adjusted: 

°F: Stop/NotOcc 

≤

 OccHeat 

≤

 (OccCool - 2).

°C: Stop/NotOcc 

≤

 OccHeat 

≤

 (OccCool - 1).

2.

The lesser of the Maximum Cool Stop and Not 

Occupied Cool setpoints determines the highest 

setting to which the occupied cool setpoint can be 

adjusted:

°F: Stop/NotOcc 

≥

 OccCool 

≥

 (OccHeat + 2).

°C: Stop/NotOcc 

≥

 OccCool 

≥

 (OccHeat + 1).

3.

The Maximum Occupied Heat Setpoint is limited 

by Occupied Cool Setpoint – 2° F (1° C).

4.

The Minimum Occupied Cool Setpoint is limited 

by the Occupied Heat Setpoint + 2° F (1° C).

1. Press Occupied Heat.

2. Press up S or down T until the desired 

temperature is displayed.

3. Press Occupied Cool.

4. Press up S or down T until the desired 

temperature is displayed.

5. Press Not Occupied Heat.

6. Press up S or down T until the desired 

temperature is displayed.

7. Press Not Occupied Cool.

8. Press up S or down T until the desired 

temperature is displayed.

9. Press Run Schedule.

NOTE: To cancel the Override and immediately return to the 

program, press Run Schedule.

A T7770 setpoint knob can remotely adjust the T7350 setpoint. 

Adjustment can be made with the sensor in override.

NOTES:

—

During override, only occupied and standby heat 

setpoints, and cool setpoints are adjusted.

—

The maximum adjustment is ±5° F (3° C).

—

With a disconnected or failed T7770, or a T7350 

not set for remote+setpoint, offset is zero.

A T7770 setpoint button can remotely adjust the T7350 

setpoint. Adjustment can be made with the sensor in override.

NOTES:

—

During override, only occupied and standby heat 

setpoints, and cool setpoints are adjusted.

—

The maximum adjustment is ±3° F (2° C).

—

With a disconnected or failed T7771, or a T7350 

not set for remote+setpoint, offset is zero.

This is a simple change to perform even with the door closed:

1. Press up S or down T until the desired 

temperature is displayed.

NOTE: If done while in Standby or Not Occupied 

mode, Temporary Occupied override engages

2. The temporary temperature appears for approximately 

ten seconds, then the room temperature is displayed.