Nady Systems U-1000 Benutzerhandbuch
18
SYSTEM OPERATION
(Note: The UH transmitter CAP (7) must be removed before installing the USB
cable.) (Note: Only one transmitter can be used with one UHF-1000 receiver. It
is not possible to use two transmitters on the same frequency and mix the
output of these transmitters into one wireless receiver. If you have any
questions, please contact the Nady Systems Customer Service Department.
See SERVICE section, pg. 21.)
cable.) (Note: Only one transmitter can be used with one UHF-1000 receiver. It
is not possible to use two transmitters on the same frequency and mix the
output of these transmitters into one wireless receiver. If you have any
questions, please contact the Nady Systems Customer Service Department.
See SERVICE section, pg. 21.)
CAUTIONS AND TROUBLESHOOTING
Feedback
Observe care in selecting P.A. volume, transmitter location and speaker
placement so that acoustic feedback, howling and screeching, will be avoided.
Please also note the pickup pattern characteristics of the microphone selected.
Omni directional mics pick up sound equally from all directions, and are prone
to feedback if not used carefully. Unidirectional mics are more resistant to
feedback, but pick up sound sources best that are directly in front of the mic.
Also, mics that are farther from the sound source, such as lavaliers, require
more acoustic gain and thus are also more prone to feedback than close-source
mics such as handheld or headworn models that are used close to the mouth.
Feedback
Observe care in selecting P.A. volume, transmitter location and speaker
placement so that acoustic feedback, howling and screeching, will be avoided.
Please also note the pickup pattern characteristics of the microphone selected.
Omni directional mics pick up sound equally from all directions, and are prone
to feedback if not used carefully. Unidirectional mics are more resistant to
feedback, but pick up sound sources best that are directly in front of the mic.
Also, mics that are farther from the sound source, such as lavaliers, require
more acoustic gain and thus are also more prone to feedback than close-source
mics such as handheld or headworn models that are used close to the mouth.
Microphone Damage
Headset and lavalier mic users, note that the microphone element can easily be
destroyed by the buildup of salts and minerals from perspiration and saliva. It is
good practice to put a windscreen on the mic at all times to protect it.
Headset and lavalier mic users, note that the microphone element can easily be
destroyed by the buildup of salts and minerals from perspiration and saliva. It is
good practice to put a windscreen on the mic at all times to protect it.
No Audio
If you’re not getting audio through the system, carefully check all setup. The
receiver and transmitter must be set to operate on the same RF channel.
If you’re not getting audio through the system, carefully check all setup. The
receiver and transmitter must be set to operate on the same RF channel.
RF Interference
If you encounter receiving interference (from other than an operating TV
station), often it can be overcome by adjusting the receiver’s squelch control.
Please note that wireless frequencies are shared with other radio services.
According to FCC regulations, wireless microphone operations are unprotected
from interference from other licensed operations in the band. If any interference
is received by any Government or non-Government operation, the wireless
microphone must cease operation or change frequencies. The above statement
is valid only for use in the U.S.A.
If you encounter receiving interference (from other than an operating TV
station), often it can be overcome by adjusting the receiver’s squelch control.
Please note that wireless frequencies are shared with other radio services.
According to FCC regulations, wireless microphone operations are unprotected
from interference from other licensed operations in the band. If any interference
is received by any Government or non-Government operation, the wireless
microphone must cease operation or change frequencies. The above statement
is valid only for use in the U.S.A.
7
OPERATING INSTRUCTIONS
UH-1000 Handheld Microphone
TRANSMITTERS SETUP
Installing Batteries
UH-1000 transmitters require 2 “AA “ size batteries to operate. Insert the
batteries according to the correct polarity as indicated. To open the battery
compartment, press the release latch and open the cover.
UH-1000 transmitters require 2 “AA “ size batteries to operate. Insert the
batteries according to the correct polarity as indicated. To open the battery
compartment, press the release latch and open the cover.
(CAUTION: Many batteries are known to have leakage problem of conductive
and corrosive liquid. Please observe the rule to remove the batteries if they are
not to be used for a period of a few days. This battery compartment is designed
to accommodate the most common size Alkaline batteries.)
and corrosive liquid. Please observe the rule to remove the batteries if they are
not to be used for a period of a few days. This battery compartment is designed
to accommodate the most common size Alkaline batteries.)
Powering the Transmitter
To turn ON, Press the POWER SWITCH (5), for 1 second.
The LCD DISPLAY (2) will flash the company and model number. Then the
menu will appear.
To turn ON, Press the POWER SWITCH (5), for 1 second.
The LCD DISPLAY (2) will flash the company and model number. Then the
menu will appear.
To turn OFF, Press the POWER SWITCH (5) for 3 seconds and release. The
transmitter will turn off.
transmitter will turn off.
Auto Turn Off function. If the transmitter Audio mute switch is in the OFF
position and the transmitter is left On. It will turn OFF after 30 minutes. This
foolproof feature will save the batteries.
position and the transmitter is left On. It will turn OFF after 30 minutes. This
foolproof feature will save the batteries.
Menu pages in Preset or User mode
Cycle Menu pages by pressing the UP (9) or DOWN (10) buttons.
Cycle Menu pages by pressing the UP (9) or DOWN (10) buttons.
Transmitter Setup Menus
Control Menus have two modes, Preset and User.
To make changes Hold the SET (8) button for 2 seconds and use the UP (9) or
DOWN (10) buttons. To save changes hold the SET (8) button for 3 seconds.
Control Menus have two modes, Preset and User.
To make changes Hold the SET (8) button for 2 seconds and use the UP (9) or
DOWN (10) buttons. To save changes hold the SET (8) button for 3 seconds.
The transmitter will remember the last Menu of User Name, Group and
Channel, or User Edit, when it is turned off. That menu will appear when it is
turned on.
Channel, or User Edit, when it is turned off. That menu will appear when it is
turned on.
1. User/Preset mode
In the Preset or User menu, hold the SET (8) button for 3 seconds. The curser
will blink. Select from User or Preset with the UP
(9) or DOWN (10) buttons. After finishing the edit
hold the SET (8) button until the curser stops
blinking.
In the Preset or User menu, hold the SET (8) button for 3 seconds. The curser
will blink. Select from User or Preset with the UP
(9) or DOWN (10) buttons. After finishing the edit
hold the SET (8) button until the curser stops
blinking.
USER MODE
PRESET MODE
PRESET MODE