Sony PDW-R1 Benutzerhandbuch
C
h
apt
er 2
Na
m
m
e
s
an
d F
d F
unc
tions
of
P
of
P
a
rts
12
2-2 Control Panel
2-2 Control Panel
a ACCESS indicator
This lights when the disc is accessed and when a file is
opened by a FAM or FTP connections (see page 72).
If the on/standby switch is set to the 1 position while this
indicator is lit, access to the disc is completed before the
unit switches to the standby state.
This lights when the disc is accessed and when a file is
opened by a FAM or FTP connections (see page 72).
If the on/standby switch is set to the 1 position while this
indicator is lit, access to the disc is completed before the
unit switches to the standby state.
Note
While the ACCESS indicator is lit, do not turn off the AC
power switch, disconnect the power cord, or remove the
battery. This could lead to a loss of data from the disc.
power switch, disconnect the power cord, or remove the
battery. This could lead to a loss of data from the disc.
b On/standby ("/
1
) switch and indicator
When the AC power switch on the rear panel is in the "
position, or a battery is loaded, this switches the PDW-R1
between the operating (") and standby (1) states. When
the switch is moved to the " position, the indicator lights.
When the switch is moved to the 1 position, the indicator
goes off.
When operating the PDW-R1 from an AC power supply,
normally leave the AC power switch in the " position, and
switch the PDW-R1 between the operating and standby
states using the on/standby switch.
position, or a battery is loaded, this switches the PDW-R1
between the operating (") and standby (1) states. When
the switch is moved to the " position, the indicator lights.
When the switch is moved to the 1 position, the indicator
goes off.
When operating the PDW-R1 from an AC power supply,
normally leave the AC power switch in the " position, and
switch the PDW-R1 between the operating and standby
states using the on/standby switch.
c Remote control switch and NETWORK access
indicator
Different positions of the switch allow different operations
as follows.
NETWORK: Enables access to the network. The
as follows.
NETWORK: Enables access to the network. The
indicator lights when an external network device is
being accessed. In this state, operation from the
control panel is not possible.
being accessed. In this state, operation from the
control panel is not possible.
LOCAL: Enables operation from the control panel.
REMOTE: Enables remote control of the PDW-R1 from
REMOTE: Enables remote control of the PDW-R1 from
a device connected to the S400 (i.LINK) connector
or REMOTE connector on the side panel.
Use extended menu item 214 “REMOTE
INTERFACE” to select which of the connectors is
used.
or REMOTE connector on the side panel.
Use extended menu item 214 “REMOTE
INTERFACE” to select which of the connectors is
used.
See 7-3-2 “Extended Menu Operations” (page 108)
for more information about how to make extended
menu settings.
for more information about how to make extended
menu settings.
d KEY INHI (key inhibit) switch
Setting this switch to ON lights the KEY INHI indicator
and disables the switches and buttons that are set to “dis”
with extended menu item 118 “KEY INHIBIT.”
Setting this switch to ON lights the KEY INHI indicator
and disables the switches and buttons that are set to “dis”
with extended menu item 118 “KEY INHIBIT.”
ACCESS
SHUTTLE
JOG
THUMB
NAIL
ESSENCE
MARK
MENU
S.SEL
SET
RESET
SHIFT
TOP
F REV
ALL/CH-1
CH-2
CH-3
CH-4
TC
F FWD
AUDIO
END
REC
PRESET
VARIABLE
PB
PREV
NEXT
PLAY
STOP
REC
CLIP
MENU
SYSTEM
MENU
MONITOR
SEL
METER
SEL
HOLD
COUNTER
SEL
SUB
CLIP
MARK1
MARK2
IN
OUT
KEY INHI
ON
OFF
NETWORK
LOCAL
REMOTE
LOCAL
REMOTE
F-RUN
R-RUN
PRESET
REGEN
INT
EXT
RP188
L/ST/R
1
ACCESS indicator
2
On/standby switch and indicator
3
Remote control switch and NETWORK access indicator
3 Jog/shuttle control block
2 Operating mode selection/menu setting section
1 Time data settings section
4
KEY INHI switch
6 Arrow buttons
5 Recording and playback control section
4 Audio settings section