Sony CC-222 Benutzerhandbuch
5 – Recording CDs—Advanced recording
28
TASCAM CC-222 Owner’s Manual
remote control unit). Prepare to play the
record on the external record player.
record on the external record player.
3
Press the
PHONO
key. The input changes to
the
RIAA PHONO
input (the
INPUT 1
PHONO
indicator lights on the display), and the disc
recorder enters record ready mode.
recorder enters record ready mode.
4
Start playing back the record.
5
Start recording on the disc by pressing the
disc
disc
PLAY
key.
The level can be adjusted using the CD
INPUT
control.
Recording will stop when the recording time
on the disc ends, or when the disc
on the disc ends, or when the disc
STOP
key
is pressed. The input source returns to the
previously-selected key.
previously-selected key.
NOTE
No keys are enabled in this phono recording mode,
except for the disc STOP key. This includes the
except for the disc STOP key. This includes the
RECORD
key, which can therefore not be used for
manual track increments (“Manual track division” on
page 26). If you want to use manual track division, use
the normal recording procedure, with the phono inputs
selected as the source.
page 26). If you want to use manual track division, use
the normal recording procedure, with the phono inputs
selected as the source.
During dubbing with auto track enabled, the trigger
level (“Setting the trigger level” on page 28) is fixed at
–24 dB and cannot be changed.
level (“Setting the trigger level” on page 28) is fixed at
–24 dB and cannot be changed.
This mode cannot be entered if a recordable disc is not
loaded in the drive.
loaded in the drive.
It is also possible to perform manual recording to
disc from the
disc from the
RIAA PHONO
source. This is the same
as the standard manual recording procedure (“Basic
recording” on page 25), except that the
recording” on page 25), except that the
PHONO
input
option should be selected (
INPUT 1 SEL
key) before
recording starts.
NOTE
It is not possible to make manual recordings from the
RIAA PHONO
RIAA PHONO
source to tape.
Advanced recording
These sections cover more advanced recording
techniques.
techniques.
Setting the trigger level
The signal level which may be used with synchro-
nized recording operations (here called the “trigger
level” or “threshold”) is set as below:
nized recording operations (here called the “trigger
level” or “threshold”) is set as below:
1 With a recordable disc loaded, press the
MENU
key until the display shows:
S_LVL>>
xxdB
, where
xx
is the current value.
2 Turn the
MULTI JOG
control or use the
SKIP
keys to change the value between
-24
,
-30
,
-36
,
-42
,
-48
,
-54
,
-60
,
-66
, and
-72
dB. (-60, -66 and -72 are only for digital).
Low numerical values of this setting (towards –24)
mean that it takes a louder signal to trigger the start
mean that it takes a louder signal to trigger the start
of the synchronized recording. A high numerical
value (towards –72) means that a relatively quiet sig-
nal will trigger the start of recording.
value (towards –72) means that a relatively quiet sig-
nal will trigger the start of recording.
When a digital source is selected, there is another
option,
option,
DD
, which means that any digital signal
above the zero level will trigger the recording.
NOTE
When dubbing from tape to disc (“Dubbing from tape
to disc” on page 27) and auto track enabled, this level is
fixed at –36 dB. When dubbing from a RIAA PHONO
source with auto track on, the level is fixed at –24 dB.
to disc” on page 27) and auto track enabled, this level is
fixed at –36 dB. When dubbing from a RIAA PHONO
source with auto track on, the level is fixed at –24 dB.