Phase Technology CI-6.2s VIII Merkblatt

CI-6.0 VIII   CI-6.1 VIII   CI-6.2s VIII   CI-7. 2 VIII   CI-7. 3 VIII  

CI-6.0 VIII   CI-6.1 VIII   CI-6.2s VIII   CI-

CI-6.0 VIII   CI-6.1 VIII   CI-6.2s VIII   CI-7. 2 VIII   CI-

2 VIII   CI-7. 3 VIII  

3 VIII  

Install instructions for CI round flush mounts models:

Using the supplied cutout template, 

carefully mark the area to be cut out. Using 
a drywall knife or saw, cut a hole in the 
drywall and prepare the speaker wires for 
connection to the speaker terminals.

8 ohms: 

Use this configuration to combine left 
and right channels for full fidelity sound 
from a single loud-speaker stereo source. 
Set jumper plugs in the stereo position. 
Connect right and left signal wires to the 
spring-loaded terminals on the rear of 
the speaker. 

 – 

When deciding upon a location, consider 

the following:
• Be certain your speaker wires can be run to or 

are accessible from these locations.

• Make certain the wall or ceiling material is 

sturdy enough to support the weight and 
vibration of the speakers.

• It is recommended that our pre-construction 

rough in brackets (part number *RB-17) be used 
whenever possible in new construction.

• Be certain the area behind the speaker is free 

of obstacles such as wall studs, electrical 
wiring, pipes, etc.

• Each speaker should be positioned properly, 

relative to the listening area for good coverage. 

• Audio performance and room-to-room isolation 

will be improved if there is some fiberglass 
insulation placed loosely behind the speaker.

Carefully replace grille by pressing it into 

the gap between the flange and the baffle. 
Enjoy your new Phase Technology speakers!

Carefully place the speaker/baffle in the 

flange 

making certain that the four V-shaped 

index marks on the outer radius of the baffle 
and the inside radius of the flange line up. 
Attach the speaker/baffle to the flange with 
the four pre-installed 1” mounting screws on 
the baffle. CAUTION Do not over-tighten.

 Using some familiar source material, 

listen to the tweeter’s balance with the level 
control in each of its three positions to find 
your favorite.

 Connect the speaker wires to the 

spring-loaded input terminals on the rear of 
the speaker, making sure no loose strands 
are exposed. If connecting the CI 6.2s 
see wiring options below.

Remove the grille from the mounting 

flange by pressing it from behind. Insert the 
mounting flange into the hole. Loosen the 
flange clamping screws one turn (counter 
clockwise) to release the clamp. Next, 
tighten all four flange clamp screws evenly 
to secure the flange to the wall.  It is best to 
tighten each screw with the same amount of 
force (torque).

stereo position

stereo position

FIG.3 – 4 ohms: Use 

this configuration to drive one channel 
(left or right) of a stereo pair with a 4 
ohm speaker load. Set jumper plugs in 
the mono position. Connect the right or 
left signal wire to the left set of posts 
on the rear of the speaker. Acoustic 
output of the speaker is increased by 
3 dB in the configuration.

4 ohms: Use this 

configuration for home theater surround 
applications. For bi-pole mode, connect 
as in the Mono/Stereo

instructions 

(FIG.3)

: 

one speaker to each surround channel. 
For di-pole mode, connect speaker 
inputs the same as Mono/Stereo 
instructions 

(FIG.3)

, but reverse the + and – 

connections of the marked tweeter wires 
to put one of the tweeters out of phase.

FIG.1 – 8 ohms: Use this 

configuration to drive one channel 
(left or right) of a stereo pair. Set 
jumper plugs in the stereo position. 
Connect the right or left signal wire to 
the right set of terminals on the rear of 
the speaker.

mono position (Bi-pole/di-pole)

Choose the appropriate mounting 

location for each speaker.