Sony HVR-1500 Benutzerhandbuch
55
Connection Using i.LINK
Chapter
Chap
ter
5
5
Conn
ec
ti
ti
ons
a
nd Se
tt
ing
s
s
f
o
r Edit
in
g
5
Connections and
Settings for Editing
Settings for Editing
Production of some of the peripherals and related devices
described in this chapter has been discontinued. For advice
about choosing devices, please contact your Sony dealer or
a Sony sales representative.
described in this chapter has been discontinued. For advice
about choosing devices, please contact your Sony dealer or
a Sony sales representative.
Connection Using i.LINK
Use in a Nonlinear Editing System
(AV/C Connection)
(AV/C Connection)
With this unit connected to a nonlinear editing system by
HDV/DV connectors, you can input and output signals in
HDV or DVCAM/DV format, and use remote control of
this unit.
The following figure shows an example of the
connections.
this unit.
The following figure shows an example of the
connections.
The i.LINK output from this unit is automatically switched
between DV/DVCAM format and HDV format, according
to the input selection and the format recorded on the tape.
Since the i.LINK stream is different for HDV or DV/
DVCAM, switching causes a bus reset on the i.LINK
interface, which may cause a problem with some
connected nonlinear editors.
In such cases, set OPERATIONAL FUNCTION
>INTERFACE SELECT: i.LINK FORMAT to i.LINK
INPUT, and select the i.LINK input format to match that
to be used.
between DV/DVCAM format and HDV format, according
to the input selection and the format recorded on the tape.
Since the i.LINK stream is different for HDV or DV/
DVCAM, switching causes a bus reset on the i.LINK
interface, which may cause a problem with some
connected nonlinear editors.
In such cases, set OPERATIONAL FUNCTION
>INTERFACE SELECT: i.LINK FORMAT to i.LINK
INPUT, and select the i.LINK input format to match that
to be used.
To connect for DVCAM/DV format
To transfer video and audio signals recorded in DVCAM/
DV format or HDV format to a nonlinear editing system in
DVCAM/DV format, make the following settings.
Here the data recorded in HDV format is output down-
converted to DVCAM/DV format.
To transfer video and audio signals recorded in DVCAM/
DV format or HDV format to a nonlinear editing system in
DVCAM/DV format, make the following settings.
Here the data recorded in HDV format is output down-
converted to DVCAM/DV format.
• The nonlinear editing system requires editing software
(not supplied) to support the DV or DVCAM format.
Note
REMOTE
AC IN
1/3
2/4
AUDIO
IN
IN
VIDEO
IN Y/S-Y/CPST
R-Y/S-C
B-Y
REF.VIDEO
VIDEO OUT
MONITOR
AUDIO
AUDIO
IN(SD/HD)
IN
OUT1
OUT2
Y/CPST
IN
IN
TC
OUT
1/2
3/4 1/2
3/4
OUT
AUDIO I/O (AES/EBU)
(SUPER)
CPST
SDI
OUT1
OUT2
HD-SDI
HDV/DV
AUDIO
OUT
OUT
1/3
2/4
Pr/R-Y/S-C
Pb/B-Y/S-Y
HDV/DV
HVR-1500 (this unit)
i.LINK (IEEE 1394) connector
i.LINK cable
(not supplied)
(not supplied)
Computer
Note
Computer settings
Settings on this unit
Install editing software
supporting the DVCAM/
DV format
supporting the DVCAM/
DV format
Remote control switch: i.LINK
INTERFACE SELECT >i.LINK
OUTPUT menu item: DV (SP) or
DVCAM
OUTPUT menu item: DV (SP) or
DVCAM
For capture:
Switching i.LINK input signal:
i.LINK:DVCAM or i.LINK:DV
Also, set the OPERATIONAL
FUNCTION >AUTO EE SELECT:
STOP and STANDBY OFF menu
items to PB.
Switching i.LINK input signal:
i.LINK:DVCAM or i.LINK:DV
Also, set the OPERATIONAL
FUNCTION >AUTO EE SELECT:
STOP and STANDBY OFF menu
items to PB.
For writing back:
Switching i.LINK input signal:
i.LINK:DVCAM or i.LINK:DV
Also, set the OPERATIONAL
FUNCTION >AUTO EE SELECT:
STOP and STANDBY OFF menu
items to EE.
Switching i.LINK input signal:
i.LINK:DVCAM or i.LINK:DV
Also, set the OPERATIONAL
FUNCTION >AUTO EE SELECT:
STOP and STANDBY OFF menu
items to EE.
Notes