Lucent Technologies Release 6 Benutzerhandbuch
DEFINITY Enterprise Communications Server Release 6
Installation and Test for Multi-Carrier Cabinets
Installation and Test for Multi-Carrier Cabinets
555-230-112
Issue 5
May 1998
Install and Wire Telephones and Other Equipment
Page 5-124
Add PRI Over PACCON to R6si
5
Add PRI Over PACCON to R6si
The optional asynchronous packet bus provided by a TN778 Packet Control
circuit pack (rather than the synchronous TDM bus provided by TN765 Processor
Interface circuit packs) can allow TN464 ISDN-PRI interfaces on an R6si system
to communicate with the system’s SPE.
circuit pack (rather than the synchronous TDM bus provided by TN765 Processor
Interface circuit packs) can allow TN464 ISDN-PRI interfaces on an R6si system
to communicate with the system’s SPE.
Tone-Clock Circuit Packs
A TN756 Tone Detector/Generator circuit pack cannot be used with PRI Over
PACCON interfaces. Therefore, replace the TN756 circuit pack with both:
PACCON interfaces. Therefore, replace the TN756 circuit pack with both:
■
TN768, TN780, TN419B, or TN2182 Tone-Clock circuit pack
■
TN748B, TN420B, or TN744C Tone Detector circuit pack
NOTE:
If a TN756 tone-detector/generator is removed from the R5si control
cabinet, the TN2182 tone clock should replace this circuit pack. The
TN2182 Tone-Clock serves to replace the tone detector circuits on
the TN756. If using a TN2182, no TN748B is required.
cabinet, the TN2182 tone clock should replace this circuit pack. The
TN2182 Tone-Clock serves to replace the tone detector circuits on
the TN756. If using a TN2182, no TN748B is required.
Expansion Interface (EI) Circuit Packs
If a new packet bus is being added to provide PRI Over PACCON for an R6si
system with an EPN, replace every TN776 EI circuit pack in the system with a
TN570 EI circuit pack. The TN570s allow packet-based communication between
the PPN and each EPN in the system.
system with an EPN, replace every TN776 EI circuit pack in the system with a
TN570 EI circuit pack. The TN570s allow packet-based communication between
the PPN and each EPN in the system.
DS1/E1 Interface Circuit Packs
Like ISDN-PRI using a TN765 Processor Interface, a TN464C (or later) DS1/E1
circuit pack is required to assign a European 32-port E1 interface.
circuit pack is required to assign a European 32-port E1 interface.
PRI Over PACCON Versus "PRI Over Processor
Interface”
Interface”
For simpler call processing, Release 6 administration does not allow packet
interface
interface
and
processor interface circuit packs to control ISDN-PRI calls for the
same
system at the
same
time. Therefore, during a PRI Over PACCON addition,
replace every TN767C DS1 circuit pack used to provide a D-channel signaling
for ISDN-PRI with a TN464F DS1 circuit pack. This frees up PI circuits to control
other important links such as DCS, CMS, and AUDIX.
for ISDN-PRI with a TN464F DS1 circuit pack. This frees up PI circuits to control
other important links such as DCS, CMS, and AUDIX.
In an R6si system with Non-Facility-Associated Signaling, a TN767C DS1 circuit
pack may still provide B channels for a PRI Over PACCON link as long as each
controlling D channel for the link (primary and optional backup) resides on a
TN464F DS1 circuit pack.
pack may still provide B channels for a PRI Over PACCON link as long as each
controlling D channel for the link (primary and optional backup) resides on a
TN464F DS1 circuit pack.