ATTO Technology 2700C Benutzerhandbuch
3
ATTO Technology Inc. iPBridge Installation and Operation Manual
1.1 ATTO iPBridge 2700R/D
The ATTO iPBridge 2700R/D is a 1-Gigabit Ethernet to Fibre Channel 1U full-rack bridge for high
performance, cost effective solutions in enterprise environments.
The iPBridge 2700R/D includes a single power
supply, four Ethernet data ports, an Ethernet
management port, a serial management port and
two Fibre Channel data ports. It includes a
battery-backed Real-Time-Clock, and an IP Time
client (RFC 1631 compliant).
Designed to fit into a 1U, full-rack enclosure, the
iPBridge 2700R/D supports side mounting so it
may be mounted into a standard 19-inch rack. The
ports and AC power are accessed from the rear of
the unit while LEDs showing port activity and
status are in the front.
Dimensions
performance, cost effective solutions in enterprise environments.
The iPBridge 2700R/D includes a single power
supply, four Ethernet data ports, an Ethernet
management port, a serial management port and
two Fibre Channel data ports. It includes a
battery-backed Real-Time-Clock, and an IP Time
client (RFC 1631 compliant).
Designed to fit into a 1U, full-rack enclosure, the
iPBridge 2700R/D supports side mounting so it
may be mounted into a standard 19-inch rack. The
ports and AC power are accessed from the rear of
the unit while LEDs showing port activity and
status are in the front.
Dimensions
Width:
17 inches
Length:
8.94 inches
Height:
1.7 inches (1U)
Weight:
8 pounds
Environment
Operating temperature:
5-40°C external
Ambient air should not exceed 40°C. User-
configurable thermal sensor for automatic
shutdown. Default is 70°C
configurable thermal sensor for automatic
shutdown. Default is 70°C
Cooling:
air enters through the slots in the rear
panel and exits through the blower on the far end
of the rear panel.
of the rear panel.
Humidity:
10-90% non-condensing
Power
Power draw:
100-260 VAC@1.7-.7 amps. ATTO
Technology, Inc. does not offer specific
international power cords. The power inlet on the
unit is a IEC320-C14. When selecting a cord, be
sure it meets all national safety compliance
requirements.
international power cords. The power inlet on the
unit is a IEC320-C14. When selecting a cord, be
sure it meets all national safety compliance
requirements.
Battery-backed event log SRAM & Real-Time-
Clock:
Clock:
A rechargeable Lithium ion battery cell
will hold the memory in a 512KB SRAM for up to
30 days.
30 days.
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
If the iPBridge has been disconnected from
power, recharging begins automatically when
power is restored to the system. The battery is
fully charged after 24 hours of continuous power
application.
Ethernet interface
The four independent 100/1000 GbE RJ45
Ethernet data ports support IP v.4 in compliance
with IEEE 802.3 GbE. Each may also be used for
iPBridge management.
A separate 10/100 Ethernet RJ45 management
port may be used for iPBridge management.
GbE cables must be at least CAT-5E certified for
1000 Mb/sec. use.
Fibre Channel interface
The two independent optical SFP 4-Gb Fibre
Channel ports auto-negotiate to 1-, 2- or 4-Gigabit
devices. They provide full support for direct
connect for F-port fabric switches, Class 3 and
intermix ANSI Fibre Channel specifications,
PLDA, public loop login (NL-ports) and fabric
connect (N-port) and full duplex transmissions.
Serial port
The RS-232 serial port provides support for
remote monitoring and
management using a DB9
connector. The baud rate is
programmable and preset at the
factory to 11500.
LED indicators
The LED indicators can be viewed from the
connector side and the front side of the iPBridge
2700R/D. (See Exhibit 1.1-2)
power, recharging begins automatically when
power is restored to the system. The battery is
fully charged after 24 hours of continuous power
application.
Ethernet interface
The four independent 100/1000 GbE RJ45
Ethernet data ports support IP v.4 in compliance
with IEEE 802.3 GbE. Each may also be used for
iPBridge management.
A separate 10/100 Ethernet RJ45 management
port may be used for iPBridge management.
GbE cables must be at least CAT-5E certified for
1000 Mb/sec. use.
Fibre Channel interface
The two independent optical SFP 4-Gb Fibre
Channel ports auto-negotiate to 1-, 2- or 4-Gigabit
devices. They provide full support for direct
connect for F-port fabric switches, Class 3 and
intermix ANSI Fibre Channel specifications,
PLDA, public loop login (NL-ports) and fabric
connect (N-port) and full duplex transmissions.
Serial port
The RS-232 serial port provides support for
remote monitoring and
management using a DB9
connector. The baud rate is
programmable and preset at the
factory to 11500.
LED indicators
The LED indicators can be viewed from the
connector side and the front side of the iPBridge
2700R/D. (See Exhibit 1.1-2)
1
9
8
7
6
5
4
3
2
RX
TX
GND