ATTO Technology 2700C Benutzerhandbuch
49
ATTO Technology Inc. iPBridge Installation and Operation Manual
6.1.7 Ethernet commands
These commands configure the management and data Ethernet ports including TCP/IP parameters.
DPMTU
Controls the MTU (Maximum Transmission Unit) used by
the Ethernet ports: Increasing the MTU may improve
throughput.
Controls the MTU (Maximum Transmission Unit) used by
the Ethernet ports: Increasing the MTU may improve
throughput.
Default: 1514
Set syntax: set DPMTU [DPn] | mp1] [1514 | 9014 ]
Requires a SaveConfiguration command
Get syntax: get DPMTU
Set syntax: set DPMTU [DPn] | mp1] [1514 | 9014 ]
Requires a SaveConfiguration command
Get syntax: get DPMTU
EthernetSpeed
Specifies the speed of the Ethernet ports. If auto is
enabled, the speed will be negotiated. Speeds 10 and 100
are half duplex 10 base T is only valid for the
management port. If you want to run the iPBridge at
10baseT, you must set the Ethernet speed using this
command. Choices are:
Specifies the speed of the Ethernet ports. If auto is
enabled, the speed will be negotiated. Speeds 10 and 100
are half duplex 10 base T is only valid for the
management port. If you want to run the iPBridge at
10baseT, you must set the Ethernet speed using this
command. Choices are:
10 = 10 baseT
100 = 100 baseT
1000 =1000baseT
100 = 100 baseT
1000 =1000baseT
Default: auto
Set syntax: set EthernetSpeed [DPn] | mp1] [10 | 100 |
1000 | Auto]
Requires a SaveConfiguration command
Get syntax: get EthernetSpeed [DPn] | mp1| all]
Set syntax: set EthernetSpeed [DPn] | mp1] [10 | 100 |
1000 | Auto]
Requires a SaveConfiguration command
Get syntax: get EthernetSpeed [DPn] | mp1| all]
Exit
Exits the current TCP/IP CLI session; it has no effect if
used during a serial CLI session.
Exits the current TCP/IP CLI session; it has no effect if
used during a serial CLI session.
Immediate command: Exit
IPAddress
Controls the IP address of the iPBridge Ethernet data
ports. If IPDHCP is enabled, the get command reports
the current IP address assigned by the network DHCP
server, followed by the DHCP identifier.
Controls the IP address of the iPBridge Ethernet data
ports. If IPDHCP is enabled, the get command reports
the current IP address assigned by the network DHCP
server, followed by the DHCP identifier.
Default IP addresses:
[10.0.0.1]
[10.0.0.2]
[10.0.0.3]
[10.0.0.4]
[10.0.0.5]
[10.0.0.2]
[10.0.0.3]
[10.0.0.4]
[10.0.0.5]
Set syntax: set IPAddress [DPn] | mp1] xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get IPAddress [DPn] | mp1| all]
Requires a SaveConfiguration command
Get syntax: get IPAddress [DPn] | mp1| all]
IPDHCP
Selecting DHCP allows the iPBridge to request an IP
address from the network DHCP server. The network
must have at least one DHCP server
Selecting DHCP allows the iPBridge to request an IP
address from the network DHCP server. The network
must have at least one DHCP server
Default: enabled
Set syntax: set IPDHCP [DPn] | mp1| all] ] [enabled |
disabled]
Requires a SaveConfiguration command
Get syntax: get IPDHCP [DPn] | mp1| all]
Set syntax: set IPDHCP [DPn] | mp1| all] ] [enabled |
disabled]
Requires a SaveConfiguration command
Get syntax: get IPDHCP [DPn] | mp1| all]
IPGateway
Controls the current gateway. If IPDHCP is enabled (see
above), get command reports the current IP gateway
assigned by the network DHCP server
Controls the current gateway. If IPDHCP is enabled (see
above), get command reports the current IP gateway
assigned by the network DHCP server
Default: 0.0.0.0
Set syntax: set IPGateway [DPn] | mp1| all]
xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get IPGateway [DPn] | mp1| all]
Set syntax: set IPGateway [DPn] | mp1| all]
xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get IPGateway [DPn] | mp1| all]
IPSubnetMask
Controls the current subnet mask. If IPDHCP is enabled
(see above), get command reports the current subnet
mask assigned by the DHCP server
Controls the current subnet mask. If IPDHCP is enabled
(see above), get command reports the current subnet
mask assigned by the DHCP server
Default: 255.255.0.0
Set syntax: set IPSubnetMask [DPn] | mp1| all]
xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get IPSubnetMask [DPn] | mp1| all]
Set syntax: set IPSubnetMask [DPn] | mp1| all]
xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get IPSubnetMask [DPn] | mp1| all]
Password
Specifies a password for all sessions: TCP/IP, FTP and
ExpressNAV web-based interface. You will be prompted
for the current password, to enter the new password, and
to confirm the new password. Passwords are case
sensitive, 0-32 characters with no spaces.An empty
password can be configured by entering the Password
confirmation prompts with no parameters. The command
RestoreConfiguration default sets the password to its
default value.
Specifies a password for all sessions: TCP/IP, FTP and
ExpressNAV web-based interface. You will be prompted
for the current password, to enter the new password, and
to confirm the new password. Passwords are case
sensitive, 0-32 characters with no spaces.An empty
password can be configured by entering the Password
confirmation prompts with no parameters. The command
RestoreConfiguration default sets the password to its
default value.
Default: Password
Set syntax: set Password
Requires a SaveConfiguration command
Set syntax: set Password
Requires a SaveConfiguration command