Sony CDX-MP70 Betriebsanweisung
31
Error displays/Messages
*1
When the CD/MD changer is connected to the unit,
the disc number of the CD or MD appears in the
display.
the disc number of the CD or MD appears in the
display.
*2
The disc number of the disc causing the error
appears in the display.
appears in the display.
If these solutions do not help improve the
situation, consult your nearest Sony dealer.
situation, consult your nearest Sony dealer.
Radio reception
Preset tuning is not possible.
• Store the correct frequency in the memory.
• The broadcast signal is too weak.
• The broadcast signal is too weak.
The stations cannot be received.
The sound is hampered by noises.
The sound is hampered by noises.
• Connect a power antenna control lead (blue)
or accessory power supply lead (red) to the
power supply lead of a car’s antenna booster.
(Only when your car has built-in FM/AM
antenna in the rear/side glass.)
power supply lead of a car’s antenna booster.
(Only when your car has built-in FM/AM
antenna in the rear/side glass.)
• Check the connection of the car antenna.
• The auto antenna will not go up.
• The auto antenna will not go up.
t Check the connection of the power
antenna control lead.
• Check the frequency.
• When the DSO mode is on, the sound is
• When the DSO mode is on, the sound is
sometimes hampered by noises.
t Set the DSO mode to off (page 22).
t Set the DSO mode to off (page 22).
Automatic tuning is not possible.
• The local seek mode is set to “on.”
t Set the local seek mode to “off” (page
• The broadcast signal is too weak.
t Perform manual tuning.
The “ST” indication flashes.
• Tune in the frequency accurately.
• The broadcast signal is too weak.
• The broadcast signal is too weak.
t Set to the monaural reception mode (page
A program broadcast in stereo is heard in
monaural.
monaural.
The unit is in monaural reception mode.
t Cancel monaural reception mode (page
t Cancel monaural reception mode (page
21).
Interference occurs during FM reception.
The wide mode is selected.
t Set the IF mode to “IF Auto” (page 21).
t Set the IF mode to “IF Auto” (page 21).
Error displays
(For this unit and optional CD/MD changers)
The following indications will flash for about
5 seconds, and an alarm sound will be heard.
5 seconds, and an alarm sound will be heard.
Blank
*
1
No tracks have been recorded on an MD.*
2
t Play an MD with recorded tracks on it.
Error
*
1
• A CD is dirty or inserted upside down.*
2
t Clean or insert the CD correctly.
• A CD/MD cannot play because of some
problem.*
2
t Insert another CD/MD.
High Temp
The ambient temperature is more than 50°C
(122°F).
t Wait until the temperature goes down
(122°F).
t Wait until the temperature goes down
below 50°C (122°F).
NO Disc
No disc is inserted in the CD/MD unit.
t Insert discs in the CD/MD unit.
t Insert discs in the CD/MD unit.
NO Mag
The disc magazine is not inserted in the CD/
MD unit.
t Insert the magazine in the CD/MD unit.
MD unit.
t Insert the magazine in the CD/MD unit.
NO Music
*
1
A CD which is not a music file is inserted.
t Insert a music CD.
t Insert a music CD.
Not Ready
The lid of the MD unit (MDX-40) is open or
the MDs are not inserted properly.
t Close the lid or insert the MDs properly.
the MDs are not inserted properly.
t Close the lid or insert the MDs properly.
Push Reset
The CD/MD unit cannot be operated because
of some problem.
t Press the RESET button on the unit.
of some problem.
t Press the RESET button on the unit.
Messages
LCL Seek +/–
The Local Seek mode is on during automatic
tuning (page 16).
tuning (page 16).
“
” or “
”
You have reached the beginning or the end of
the disc and you cannot go any further.
the disc and you cannot go any further.