Samsung WA78K1 Benutzerhandbuch
The User’s Manual is for common use.
Make use of the User’s Manual depending upon your washing machine model.
INSTALLATION & MAINTENANCE
ENVIRONMENT
Leave some space
Maintain at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak surface, noise or
vibration occurs. (Allowable is 1˚)
Adjust the legs for even placement.
Leave some space
Maintain at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak surface, noise or
vibration occurs. (Allowable is 1˚)
Adjust the legs for even placement.
Never install the washer near water.
Do not place the washer in steamy rooms or where the
washer is directly exposed to rain.Moisture may destroy the
electrical insulation causing an electrical shock hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected by direct
heat,never place the washer near furnaces, boilers, etc.
Do not place under direct sunlight.
Do not place the washer in steamy rooms or where the
washer is directly exposed to rain.Moisture may destroy the
electrical insulation causing an electrical shock hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected by direct
heat,never place the washer near furnaces, boilers, etc.
Do not place under direct sunlight.
•
If the washer is not leveled with the ground, it makes the machine tremble more or be out of order.
So, make sure that the washer is leveled properly.
LEVELLING
SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING
THE POSITION OF THE WASHING TUB.
THE POSITION OF THE WASHING TUB.
Lock
Loosen
•
Open the lid of the machine, pour water into the tub up to the level
just below the pulsator, and adjust the legs so that the pulsator is
positioned at the center of the water as shown in the figure.
positioned at the center of the water as shown in the figure.
•
Place the machine more than 10cm away from the wall.
•
Adjust the legs on feet for levelling .
1. Remove the adaptor
from the water
supply hose.
from the water
supply hose.
2. First,using a "+" type scre driver,
loosen the four screws on the adaptor.
Next,take the adaptor and turn part(b)
following the arrow for gap about 5mm
between them.
loosen the four screws on the adaptor.
Next,take the adaptor and turn part(b)
following the arrow for gap about 5mm
between them.
3. Connect adaptor to the water tap by
tightening the screws firmly.
Then, turn part (b) following the arrow
and put (a) and (b)together.
tightening the screws firmly.
Then, turn part (b) following the arrow
and put (a) and (b)together.
4. Connect the water supply hose to the adaptor.
Pull down the part (c) of the water supply
hose .When the part (c)is released,
the hose is automatically connected to
the adaptor making a 'click' sound.
Pull down the part (c) of the water supply
hose .When the part (c)is released,
the hose is automatically connected to
the adaptor making a 'click' sound.
a
b
a
b
c
CONNECTING THE WATER SUPPLY HOSE
5. Connect the other end of the water
supply hose to the inlet water valve at the
back of the washer. Screw the hose
clockwise all the way in.
supply hose to the inlet water valve at the
back of the washer. Screw the hose
clockwise all the way in.
5-1.Connect the other end of the water
supply hose to the inlet water valve
at the top of the washer.
Screw the hose clockwise all the way in.
supply hose to the inlet water valve
at the top of the washer.
Screw the hose clockwise all the way in.
If the water tap is a screw type,assemble
a water supply hose that fits to the
tap as shown.
a water supply hose that fits to the
tap as shown.
NOTICE After completing connection, if water leaks from the hose,
then repeat the same steps.
Use the most conventional type of faucet for water supply.
In case the faucet is square or too big,remove the spacing
ring before inserting the faucet into the adaptor.
then repeat the same steps.
Use the most conventional type of faucet for water supply.
In case the faucet is square or too big,remove the spacing
ring before inserting the faucet into the adaptor.
ASSEMBLING THE RAT PROTECTION PANEL
1.Insert the sound
absorbing panel
to the assembling
hole on back side
to the end.
absorbing panel
to the assembling
hole on back side
to the end.
2.If you have difficulty
inserting the panel
lift up the washer a
little and insert it
inserting the panel
lift up the washer a
little and insert it
Install the drain hose in the
position of about 90~100cm
above the ground.
position of about 90~100cm
above the ground.
Be sure to join tightly the drain
hose into the drain-outlet
on the side of the machine.
hose into the drain-outlet
on the side of the machine.
Be sure to join tightly the drain hose into
the drain-outlet on the back of the
machine.
the drain-outlet on the back of the
machine.
Take out the cap-hose and
connect the outlet-hose.
connect the outlet-hose.
IN CASE OF PUMP-DRAINED WASHER
cap-hose
outlet-hose
70~80cm
90~100cm
5
WA80N-BP5-02197A-GB-0616ÃÑ.indd 6
WA80N-BP5-02197A-GB-0616ÃÑ.indd 6
2005-06-17 ¿ÀÈÄ 1:44:06
2005-06-17 ¿ÀÈÄ 1:44:06