Sony CDX-GT270MP Benutzerhandbuch
10
Adjusting setup items
1
Press
, rotate the control dial
until the desired category appears, then
press it.
press it.
2
Rotate the control dial until the desired
item appears, then press it.
item appears, then press it.
3
Rotate the control dial to select the
setting, then press it.
setting, then press it.
*
The setting is complete.
4
Press
(BACK) to return to the
previous display.
* For CLOCK-ADJ and BTM settings, step 4 is
not necessary.
The following items can be set depending
on the source and setting:
on the source and setting:
GENERAL:
*1 When the unit is turned off.
*2 When the tuner is selected.
SOUND:
CLOCK-ADJ
(Clock Adjust) (page 4)
CAUT ALM
*
1
(Caution Alarm)
Activates the caution alarm: “ON,”
“OFF” (page 4).
“OFF” (page 4).
BEEP
Activates the beep sound: “ON,” “OFF.”
AUTO OFF
Shuts off automatically after a desired
time when the unit is turned off: “NO,”
“30S (Seconds),” “30M (Minutes),” “60M
(Minutes).”
time when the unit is turned off: “NO,”
“30S (Seconds),” “30M (Minutes),” “60M
(Minutes).”
AUX-A
*
1
(AUX Audio)
Activates the AUX source display: “ON,”
“OFF” (page 11).
“OFF” (page 11).
REAR/SUB
*
1
Switches the audio output: “REAR-
OUT” (power amplifier), “SUB-OUT”
(subwoofer).
OUT” (power amplifier), “SUB-OUT”
(subwoofer).
CT
(Clock Time)
Activates the CT function: “ON,” “OFF”
(page 8).
(page 8).
BTM
*
2
EQ3 LOW
*
1
EQ3 MID
*
1
EQ3 HIGH
*
1
BALANCE
Adjusts the sound balance: “RIGHT-15
(R15)” – “CENTER (0)” – “LEFT-15
(L15).”
(R15)” – “CENTER (0)” – “LEFT-15
(L15).”
FADER
Adjusts the relative level: “FRONT-15
(F15)” – “CENTER (0)” – “REAR-15
(R15).”
(F15)” – “CENTER (0)” – “REAR-15
(R15).”
LOUDNESS
Reinforces bass and treble for clear
sound at low volume levels: “ON,”
“OFF.”
sound at low volume levels: “ON,”
“OFF.”
S.WOOFER
*
2
(Subwoofer)
SW LEVEL
(Subwoofer Level)
Adjusts the subwoofer volume level:
“+10 dB” – “0 dB” – “–10 dB.”
(“ATT” is displayed at the lowest
setting.)
SW PHASE
“+10 dB” – “0 dB” – “–10 dB.”
(“ATT” is displayed at the lowest
setting.)
SW PHASE
(Subwoofer Phase)
Selects the subwoofer phase: “SUB
NORM,” “SUB REV.”
LPF
NORM,” “SUB REV.”
LPF
(Low Pass Filter)
Selects the subwoofer cut-off frequency:
“OFF,” “80Hz,” “100Hz,” “120Hz,”
“140Hz,” “160Hz.”
“OFF,” “80Hz,” “100Hz,” “120Hz,”
“140Hz,” “160Hz.”
HPF
(High Pass Filter)
Selects the front/rear speaker cut-off
frequency: “OFF,” “80Hz,” “100Hz,”
“120Hz,” “140Hz,” “160Hz.”
frequency: “OFF,” “80Hz,” “100Hz,”
“120Hz,” “140Hz,” “160Hz.”