Sony PEGA-CC5 Installationsanleitung

•Choose the installation location carefully, such

that the unit will not interfere with normal
driving operations.

•Avoid installing the unit in areas subject to dust,

dirt, excessive vibration or high temperatures,
such as in direct sunlight or near heater ducts
under the floor carpet.

•Use only the supplied mounting hardware for a

safe and secure installation.

Attaching condition (see fig.4)

This unit is attached to the dashboard of a car, and
side fin of the air vent.
The mounting attachment can be attached to an
air vent whose dimensions and shape meet
both conditions 

Mounting support arm and
rubber blocks (see fig.5)

Combining the support arm 6and the support arm
7

 with rubber blocks 8, attach them to the

mounting attachment 5.
Depending on the dimensions and shape of the
dashboard and the air vent, choose the support
arms so that the rubber blocks 8 are placed on the
top and bottom outer edges of the air vent.

Notes
• Choose a combination of rubber blocks 8, the

support arm 6 and the support arm 7 so that the
rubber blocks 8 do not block the air vent.

board and the air vent, the mounting attachment 5
can sometimes be attached without the support arm
6

 or the support arm 7.

Installing the mounting
attachment (see fig.6)

Choose either the holding clip (S) 9 or the
holding clip (L) 0, depending on the width of
the side fin of the air vent.

1

Insert the holding clip into the air
vent and hook the holding clip on
the side fin.

2

 Adjust the attachment position so that

the holding clip does not touch the
back fin. If you insert the holding clip
forcibly, the back fin may be damaged.

With the holding clip hooked on the side fin
of the air vent, feed the holding clip into the
hole on the back of the mounting attachment,
and pull the holding clip until the mounting
attachment becomes stable.

Tip (6-

*

If the rubber blocks 8 of the car cradle slip and the car
cradle cannot be attached to the dashboard securely,
attach it using the two-sided tape qg between the
rubber blocks 8 and the dashboard. The two-sided
tape qg can be cut. Cut it to a size larger than the
rubber block 8 itself. The two-sided tape qg is
ineffective if it is cut too small.
Please consult a qualified technician or service
personnel if you cannot attach the car cradle to the car
securely.

1

 Press the lever on the bottom of the

mounting attachment.

2

 Loosen the holding clip by pulling the

mounting attachment forward.

1

 Press the mounting attachment to the air

vent.

2

 Twist the mounting attachment slightly.

3

 Pull the mounting attachment off towards

you.

Attaching the holding arms
 (see fig.7)

Depending on the type of the CLIÉ handheld (short
screen or long screen), choose the holding arm 2,
the holding arm 3 or the holding arm 4.

Short screen type (PEG-TG50)
“Size S” is marked on the back of
the holding arm 2.

Long screen type (PEG-NX73V)
“Size L” is marked on the back of
the holding arm 3.

Long screen type 2 (PEG-TH55)
“Size L2” is marked on the back of
the holding arm 4.

Remove the sheet attached to the car cradle.
When removing the sheet, be careful not to let
any objects get into the slots of the car cradle.

Attach the holding arms chosen according to
the type of CLIÉ handheld.
1

 Insert the holding arms’ tab 

 into the car

cradle.

2

 Pull both sides of the holding arms outwards

and insert the tab  .

Detaching the holding arms
When replacing the holding arms to use the
different type of CLIÉ handheld, etc., insert the tip
of a slotted screwdriver into the slot for the tab 
and release the lock of the tab. There are two tabs:
one on the left and one on the right.

Mounting the car cradle to the
mounting attachment (see fig.8)

1

Slide the tip of the mounting attachment along
the rail on the back of the car cradle to mount it.

2

Rotate the dial 

 to fix the car cradle.

Attaching your CLIÉ handheld
(see fig.9)

Mounting
1

 Mount your CLIÉ handheld on the connector of

the car cradle.

2

 Tilt back your CLIÉ handheld rest in the car

cradle.

Adjusting the angle (see fig.0)

Adjust the angle of the car cradle by dial   of the
mounting attachment.

Attaching a GPS aerial (see fig.qa)

•Install the GPS aerial qs on the dashboard.
•Install the GPS aerial qs on a flat surface to keep it

horizontal.

•Choose the attachment position where the best

reception is achieved. Also, choose the position
where no obstacle blocks the reception from the
GPS satellite.

Note
Some types of front windscreen do not let the radio
wave from a GPS satellite pass.
If the reception of the radio wave is poor when the GPS
aerial qs is attached to the inside, attach it to the
outside of the car roof.

Before attachment
• Make sure that the GPS aerial qs has good

reception and not hidden behind car ornaments,
the windscreen wiper, etc.

• Make sure that the GPS aerial qs does not disturb

operation of car equipment.

• Clean the mounting surface.

Remove the release-coated paper from the
surface of the base sheet qd, and then place
the GPS aerial qs on the centre of the base
sheet qd.

Remove the release-coated paper from the
back surface of the base sheet qd, and stick
the base sheet qd to the mounting surface.

• Fix the cord of the GPS aerial qs using the cord clamps

qf

• Attach the cord clamps qf after cleaning the

•Attach the GPS aerial qs horizontally in a place

where GPS satellite reception is not blocked by
the car roof.

•The GPS aerial qs is attached by a magnet.

When attaching it on the car, place it carefully, so
as not to harm the car’s body surface.

When attaching to a car of aluminum or FRP
body
Since the magnet will not stick to aluminum or
FRP, attach the GPS aerial qs to the inside of the
car.

Before attachment
Clean the mounting surface.

Attach the GPS aerial qs to the roof.
Clean the 

mounting

 surface before attaching.

Place the GPS aerial
qs

the base sheet qd.

qs

qd

1

1

2

1

2

qf

Roof A
Pass the GPS aerial cord over the roof, passing
the windscreen pillar, fender and molding, and
then pull it inside of the car.

Roof B
Pass the GPS aerial cord over the roof, passing
the centre pillar, windscreen pillar inner side
and dashboard, and then pull it into the car.

qf

On painting of the GPS aerial
The GPS aerial qs can be painted to match the car’s
body colour. However, do not use metallic paint, as
it may cause poor reception or reception error.
Also, when painting, do not dismantle the aerial.

Connecting the car battery
adapter (see fig.qs)

Connect the car battery adapter qa to the DC 5.2V
connector of car cradle (1), and connect the car
battery adapter qa into the cigarette lighter socket
(2).

Notes
• Do not plug the car battery adapter qa into the

• To fix the cord of the car battery adapter qa, use the

cord clamps qf if necessary.
Clean the mounting surface before attaching the cord
clamps.

Detaching your CLIÉ handheld
(see fig.qd)

Detaching
1

 Squeeze both RELEASE buttons simultaneously

with one hand.

2

 Pull out the CLIÉ handheld towards you from

the top with your other hand.

qs

qa