Honeywell intelliguard 9000 Benutzerhandbuch

3

74-3035—2

Wiring Connections: Table 1 describes the connections 

between the I9000 CU and its input and output devices. Use a 

RS-232 cable to connect the CU to the EBI. Use twisted pair 

cable to connect the RS-485 CU ports to the I9000 input and 

output devices.

NOTE: All devices should be equally divided among the two 

RS-485 communication lines to maximize system 

performance. See Control Center 2 Keypads and 

Area Keypads sections for details.

Enclosure: 0.06 in. (1.52 mm) cold rolled steel.

Dimensions:  14-7/16 in. (367 mm) wide x 10-5/16 in. (262 

mm) high x 3-1/8 in. (79 mm) deep.

Weight:  8.66 lb (3.93 kg), without batteries.

Approvals: UL, ULC, CE.

NOTE: Device to CU wire gauge is 22 AWG. Voltage drops 

due to load and cable length may require an increase 

in conductor size to ensure devices remain within 

operational limits.

The I9000 and the RIPS operate from 16 Vac, 50/60 Hz (37 to 

40 VA) provided by a locally supplied power transformer. For 

ULI installations, this is a Silent Knight model 9220 

Transformer with Silent Knight model 4165 Enclosure or listed 

equivalent. For ULC installations (Canada only), this is a 

5660-051 Honeywell Transformer Assembly.

A Remote Intelligent Power 

Supply (RIPS) consists of an 

I9000 enclosure containing the 

8003-295 Intelligent Switching 

Power Supply (ISP) without an 

ICP II Control Board. The RIPS 

is required when the installation 

power requirements exceed the 

available control unit power. 

Each I9000 CU supports a maximum of seven RIPS. The 

control unit supports up to eight ISPs (four per RS-485 port), 

seven in the RIPS (one per RIPS) and one located in the 

I9000 control unit enclosure. Depending on the installation 

power backup requirements, up to two batteries can be 

connected to each ISP. When the programmable outputs are 

used, two batteries are recommended for those respective 

RIPS.

• Same as ISP features except the tamper input is factory 

wired to the RIPS enclosure tamper switch.

• When cover is closed, the red LED Communication 

Indicator is automatically disabled to save power.

Model: 8003-217 Remote Intelligent Power Supply (RIPS).

Transformer Electrical Ratings: Each RIPS must have its 

own transformer connected to a non-switched electrical cir-

cuit.

Type: Class II Energy Limiting.

Output Voltage: 16 Vac.

Output Current: 2.3A.

Power Rating: 37 VA.

Operating Voltage: 13.6 Vac to 17.6 Vac.

ISP Power Consumption During AC Failure: 20 mA at 

13.8 Vdc (maximum battery voltage). Add programmable 

output load current to this value if the output is used.

Outputs: 2 x 400 mA maximum at 12.9 Vdc ± 4%. One pro-

grammable switched output at 1A, 12 Vdc.

NOTE: Power for the ISP programmable switched output is 

partly obtained from the standby batteries. There-

fore, this output should be used to drive loads such 

as sirens and bells for short durations (15 minutes 

maximum). Otherwise the battery capacity will be 

reduced and this will affect the total backup time 

available for the devices connected to that ISP.

Model: YUASA P/N NP7-12 or equivalent.

Electrical Ratings: 12V, 7 Ah.

Type: Sealed lead acid.

Quantity: Two maximum. 

Dimensions: 2-9/6 in. (65 mm) wide x 3-7/8 in. (98 mm) high 

(including terminals), x 6 in. (152 mm) deep.

Weight: 6.17 lb (2.65 kg).

Communication: RS-485 receiving and transmitting signals.

Enclosure: 0.06 in (1.52 mm) cold rolled steel.

Dimensions: 14-7/16 in. (367 mm) wide x 10-5/16 in. 

(262 mm) high x 3-1/8 in. (79 mm) deep.

Weight:  8.62 lb (3.91 kg).

Approvals: UL, ULC, CE.

Application

I9000 CU and 

peripherals

EBI Interface

Electrical Interface RS-485

RS-232

Cable

Twisted Pair (two or 

three pairs)

Shielded Cable, 

four conductors

Maximum Distance 3277 ft (999m)

75 ft (22m)

Baud Rate

4800 Baud

75-2400 Baud, 

Programmable

Word Format

10 Bits (Start, 7 

Data, Even Parity, 

Stop)

12 Bits (1 Start, 8 

Data, 1 Parity, 2 

Stop)