Knoll Systems Door MR64 Benutzerhandbuch
necessary to have the source wires connected
to program the MR64 labels.
to program the MR64 labels.
Using the back of this manual, please write
down the source name connected to source A,
source B, source C and source D.
source B, source C and source D.
Turn the MVP44a, MVP64a on using the power
button on the front panel or the MR640 by
connecting the power supply. As soon as the
power is turned on the MR64 will first show
connecting the power supply. As soon as the
power is turned on the MR64 will first show
which software revision it is programmed with,
display “Knoll Systems” and then display
display “Knoll Systems” and then display
“System Off”.
Labels can only be programmed or changed by
entering the MR64 installer menu when the LCD
entering the MR64 installer menu when the LCD
displays “System Off”. All of the available labels
are the same for all four sources.
are the same for all four sources.
To enter the installer menu from “System Off”
press the MR64 keypad (not remote) MUTE
press the MR64 keypad (not remote) MUTE
button for about 1 second then immediately
press the INPUT for about 5 seconds. Release
press the INPUT for about 5 seconds. Release
the INPUT button as soon as the LCD displays
SET A
Source A
Source A
Now press the UP or DOWN buttons next to
the INPUT buttons to scroll through the label
selections for source A on the bottom row of
selections for source A on the bottom row of
the LCD display. When the correct selection is
displayed press the MUTE button to confirm
displayed press the MUTE button to confirm
this choice.
Note: If a mistake is made, go though the
Note: If a mistake is made, go though the
rest of the programming setup and restart
the installer mode again.
the installer mode again.
The LCD display then displays
SET B
Source B
As above press the UP or DOWN buttons next
to the INPUT buttons to scroll through the
to the INPUT buttons to scroll through the
label selections for source B on the bottom row
of the LCD display. When the correct selection
of the LCD display. When the correct selection
is displayed press the MUTE button to confirm
this choice. The LCD display then displays
this choice. The LCD display then displays
SET C
Source C
Source C
As above press the UP or DOWN buttons next
to the INPUT buttons to scroll through the
to the INPUT buttons to scroll through the
label selections for source C on the bottom row
of the LCD display. When the correct selection
of the LCD display. When the correct selection
is displayed press the MUTE button to confirm
this choice. The LCD display then displays
this choice. The LCD display then displays
SET D
Source D
As above press the UP or DOWN buttons next
to the INPUT buttons to scroll through the
label selections for source D on the bottom row
of the LCD display. When the correct selection
label selections for source D on the bottom row
of the LCD display. When the correct selection
is displayed press the MUTE button to confirm
this choice. The LCD display then displays
this choice. The LCD display then displays
System
Off
And the MR64 labels have been set. To change
any of the labels you can re-enter the installer
menu and scroll through all four labels and
any of the labels you can re-enter the installer
menu and scroll through all four labels and
reset the ones needed.
OFF
VOL
Infrared
receiver
LCD display
Mute
button
Volume up
and down or
source select or
sets backlighting
Shut off this room
or shut off whole
house (press for
5 seconds).
Input
select
button
ALL
MUTE
INPUT
MR64
Line 1
Line 2
Volume
select
button
All button for
whole house
functions
RB8 Remote Control Functions
Power: switches
room off or whole
house off(press
for 5 seconds)
POWER
MUTE
VOL
-
+
4
3
2
1
INPUT
RB8
systems
Input 1-4: Turns
on room and
selects input
music source
Mute: Mutes music.
to restore, press
mute, input 1-4 or
volume up/down
Volume Up/Down
Press and hold
for continuous
volume changes