Acclaim Lighting ACL7500U1 Benutzerhandbuch

It is very important that you fully charge the batteries in your new sound system before the first time its used. To preserve battery life it is also

recommended that batteries be fully charged as soon as possible after every use regardless of the length of operation.
UNDERSTANDING THE BATTERY LEVEL INDICATOR LIGHT

LED Flashing Red

Battery charge is very low, in 15-30 minutes the Battery Protection Circuit will turn the system off

LED Off

Battery is completely drained and must be charged

OPERATING ACCLAIM IN AC MODE
Plug your sound system into an AC outlet and operate as normal while charging the built-in batteries at the same time. The Charger LED will

light during charging and flash when the battery is fully charged.
BATTERY SERVICE TIME
With the batteries fully charged you can expect approx.:

6-8 hrs @ Medium Volume 2-4 hrs @ Full Volume

Of continuous music input

(longer for speech)

. However service time will vary depending on control settings and the use of accessories

(built-in

CD player, wireless receivers and/or a companion speaker).

SYSTEM STORAGE & BATTERIES
Always store your sound system with the batteries fully charged. For extended periods of storage leave the system plugged into an AC outlet. If

this is not possible, charge the system at least once each month for a minimum of 24 hours.

An automatic charging system is built-in to your Acclaim Lectern Sound System. It is designed to properly charge and maintain the systems

built-in batteries. To charge the batteries:

1.  Plug the power cord into your sound system
2.  Plug the other end of the cord into AC outlet

(Charger LED will stay on during charging)

3.  Batteries will be fully charged in approximately 6-8 hrs

(Charger LED will flash)

When in AC mode the system automatically transfers power from the battery charger to the power amplifier at high volume output, causing the

Charger LED to flicker.

AN-1001X - Companion Speaker

Unpowered companion speaker

(speaker cable not included)

SC-50 - Heavy Duty Speaker Cable

50’ speaker cable, connect AN-1001X to powered Acclaim
SS-550 - Heavy Duty Speaker Stand

Adjustable stand made of black, anodized aluminum

ACC-BASE - Base for Acclaim

Acclaim lectern base & traveling case
MIC-90 - Handheld Wired Microphone

Anchor’s dynamic, balanced, low impedance microphone w/ unidi-

rectional pick-up pattern, mic “on/off” switch & 20’ cable

ANCHOR WIRELESS - 16 CHANNEL UHF

WH-6000 - Handheld Microphone/Transmitter

Wireless transmitter & microphone in one unit

WB-6000 - Body Pack Transmitter

Works w/ hands free microphones

(mic not included)

Body Pack Transmitter Microphones:

CM-60 - Collar Microphone

Lightweight, low-profile mic
EM-60T - UltraLite Microphone

Hands free “Over-the-Ear” mic

LM-60 - Lapel Microphone

Lightweight, clip-on lapel mic
HBM-TA4F - Headband Microphone

Ultra-lightweight headband mic

Anchor Audio UHF wireless is a 16 channel, diversity wireless system that receives signals with two independent antennae. With diversity

wireless the receiver processes the stronger signal, effectively minimizing dropouts and interference from other transmitting sources. The

antennae are mounted internally so there are no obstructions or risk of damage.
CHANNEL SELECTION - BUILT-IN RECEIVER
Select a channel, set the built-in receiver and micro-

phone transmitter to that channel before using your

wireless system.

1.  Choose any available wireless channel/

frequency from 1 thru 16 

(transmitter instructions - page 7)

2.  Set the Wireless Channel Selector Knob to

the channel/frequency you choose in step

1 above

Remember,  to  operate  the  receiver  &  transmitter

pair must be set to the same channels.

WIRELESS MICROPHONE 

VOLUME CONTROL

WIRELESS RECEIVER CHANNEL 

SELECTION KNOB

RX INDICATOR LIGHTS

BATTERY LEVEL  

INDICATOR LIGHT

CHARGER  

INDICATOR LIGHT