Behringer X-USB Anleitung Für Quick Setup
Warning
Failure to observe the following warnings may
lead to fatality or serious injury from fire or
lead to fatality or serious injury from fire or
electric shock.
Before installing the card, you must refer to the owner’s
manual of the host device or to behringer.com to verify that
your host device supports this card, and to verify the number
of cards that can be installed in combination with other
BEHRINGER or third-party cards.
• Do not attempt to disassemble or modify the card.
Before installing the card, you must refer to the owner’s
manual of the host device or to behringer.com to verify that
your host device supports this card, and to verify the number
of cards that can be installed in combination with other
BEHRINGER or third-party cards.
• Do not attempt to disassemble or modify the card.
Do not apply excessive force to board connectors or
other board components. Mishandling of board may
lead to shock, fire hazard, or equipment failure.
other board components. Mishandling of board may
lead to shock, fire hazard, or equipment failure.
• Disconnect the power cable from the main unit before
installing this card to eliminate shock hazard.
Caution
Failure to observe the following precautions may
lead to personal injury, or may result in damage
Failure to observe the following precautions may
lead to personal injury, or may result in damage
to equipment or other property.
• Do not touch the board’s metallic leads (pins)
• Do not touch the board’s metallic leads (pins)
when handling the card. Pins are sharp and may
cause injury.
cause injury.
• The card is electrostatic-sensitive.
Before handling the card, you should briefly
touch the main unit’s metal casing with
your bare hand so as to drain off any static
charge from your body. BEHRINGER assumes no
responsibility for data loss, equipment damage,
or injury caused by inappropriate handling or usage.
touch the main unit’s metal casing with
your bare hand so as to drain off any static
charge from your body. BEHRINGER assumes no
responsibility for data loss, equipment damage,
or injury caused by inappropriate handling or usage.
1. IMPORTANT NOTICE: DO NOT MODIFY
THIS UNIT! This product, when installed as indicated
in the instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
BEHRINGER may void your authority, granted by the FCC,
to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product, use only high quality
shielded cables. Cables supplied with this product MUST be
used. Follow all installation instructions. Failure to follow
instructions could void your FCC authorization to use this
product in the USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will not
result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in
the users manual, may cause interference harmful to the
operation of other electronic devices. Compliance with FCC
regulations does not guarantee that interference will not
occur in all installations. If this product is found to be the
source of interference, which can be determined by turning
the unit “OFF” and “ON”, please try to eliminate the problem
by using one of the following measures: Relocate either this
product or the device that is being affected by the interference.
Utilize power outlets that are on different branch circuits
(circuit breaker or fuse) or install AC line filters. In the case of
radio or TV interference, relocate/reorient the antenna. If the
antenna uses 300 Ohm ribbon cable, use coaxial cable instead.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distribute
this type of product. If you can not locate the appropriate
retailer, please contact BEHRINGER customer service.
2. IMPORTANT: When connecting this product to
accessories and/or another product, use only high quality
shielded cables. Cables supplied with this product MUST be
used. Follow all installation instructions. Failure to follow
instructions could void your FCC authorization to use this
product in the USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will not
result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in
the users manual, may cause interference harmful to the
operation of other electronic devices. Compliance with FCC
regulations does not guarantee that interference will not
occur in all installations. If this product is found to be the
source of interference, which can be determined by turning
the unit “OFF” and “ON”, please try to eliminate the problem
by using one of the following measures: Relocate either this
product or the device that is being affected by the interference.
Utilize power outlets that are on different branch circuits
(circuit breaker or fuse) or install AC line filters. In the case of
radio or TV interference, relocate/reorient the antenna. If the
antenna uses 300 Ohm ribbon cable, use coaxial cable instead.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distribute
this type of product. If you can not locate the appropriate
retailer, please contact BEHRINGER customer service.
FCC INFORMATION U.S.A.
10 X-USB Interface Operation Guide