High End Systems High End LCD Controller for Studio Color Benutzerhandbuch
Studio Color LCD Controller
Master and Slave Controllers 2-21
2
1.
Set personality switch B-1 on the rear panel of each slaved
controller to ON. Refer to Figure 2-1 on page 2-2 for the
location of the switches. The Slave LED (located above the
Power key switch) turns ON.
controller to ON. Refer to Figure 2-1 on page 2-2 for the
location of the switches. The Slave LED (located above the
Power key switch) turns ON.
2.
Connect a shielded, 2-conductor cable with a 6 mm (1/4 inch)
tip/ring/sleeve connector on each end from the master
controller's Master (out) connector located on the rear panel
to the slave controller's Slave (in) connector.
tip/ring/sleeve connector on each end from the master
controller's Master (out) connector located on the rear panel
to the slave controller's Slave (in) connector.
3.
To slave more than one controller to a master controller,
continue connecting cables from one controller to the next, as
shown in Figure 2-13 on page 2-18.
continue connecting cables from one controller to the next, as
shown in Figure 2-13 on page 2-18.
Figure 2-15. Location of the Master and Slave ports
on the controller’s rear panel.
on the controller’s rear panel.
DATA LINK
OUT
CAUTION
WARNING
PERSONALITY
SLAVE
MASTER
RS-232
SERI AL PORT
1-6
ANALOG INPUTS
7-12
REMOTE
ENABLE
FUSE
CAUTI ON
voltage
select
1 2 3 4
A
B
M I DI
IN
OUT
STEREO
AUDIO
INPUT
INPUT
11
5
T o reduce t he ri sk of f ire or
electr ic shock, do not expose
this device to rain or m ois ture.
electr ic shock, do not expose
this device to rain or m ois ture.
L
R
R
IMPORTANT SAFETY INFORMATION. SEE INSTRUCTION MANUAL BEFORE USE.
WICHTIGE SICHERHEITSINFORMATIONEN. BEDIENUNGSANLEITUNG VOR GEBRAUCH LESEN!
D'IMPORTANTE CONSIGNE DE SÉCURITÉ. VOYEZ LE MANUEL D'INSTRUCTION AVANT L'UTILISATION DE L'APPAREIL.
WICHTIGE SICHERHEITSINFORMATIONEN. BEDIENUNGSANLEITUNG VOR GEBRAUCH LESEN!
D'IMPORTANTE CONSIGNE DE SÉCURITÉ. VOYEZ LE MANUEL D'INSTRUCTION AVANT L'UTILISATION DE L'APPAREIL.
This device complies wi th part 15 of the FCC rules.
Operation i s subject to t he f ollowing two conditions:
(1) This device may not cause harmful interferences,
and (2) this device mus t accept any interference
that may cause undesi red operation.
Operation i s subject to t he f ollowing two conditions:
(1) This device may not cause harmful interferences,
and (2) this device mus t accept any interference
that may cause undesi red operation.
To prevent electric shock, do
not remove cover. No user
serviceable parts inside.Refer
servicing to qualified service
personnel. Replace fuse with
same type and rating.
not remove cover. No user
serviceable parts inside.Refer
servicing to qualified service
personnel. Replace fuse with
same type and rating.
R AT IN G IN FO R MAT IO N
V OL TA G E : 1 1 5V AC /2 3 0V AC
C U R R EN T : 0.2 5A/0 .1 5 A
F R E Q UE N C Y : 5 0 -60 H Z
V OL TA G E : 1 1 5V AC /2 3 0V AC
C U R R EN T : 0.2 5A/0 .1 5 A
F R E Q UE N C Y : 5 0 -60 H Z
115 V 0.5 A, SLOW BLOW
230 V 0.315 A, SLOW BLOW
230 V 0.315 A, SLOW BLOW
1 2 3 4
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Master (out)
port
Slave (in)
port
MODEL
SERIAL
DATE
QC
VOLTAGE
HZ
230
15FM123456
Cy berlight LCD Controller
50
80
59
000
1
ETL Listed
C onforms to
U L Std. 1950
U L Std. 1950
C ertified to
C AN /CSA C 22.2 No. 950
67501
R
C
R
LIGHTWAVE RESEARCH
2217 West Braker Lane
Austin, Texas U.S.A.
2217 West Braker Lane
Austin, Texas U.S.A.