Maxon Telecom Modem MM-6280IND Benutzerhandbuch
HSDPA Standard At Commands Page 59 of 60 Version 1.2
Q u a l c o m m c o m m a n d s
Table 43. Qualcomm command
COMMAND
Description
Operation
Support
$QCCLR
clear mobile error log
Clears the mobile error log
Supported
$QCDMG
transition to diagnostics
monitor operation
monitor operation
Returns OK and then transitions the
mobile’s serial port to DM mode; DM
mode runs at rate set by $QCDMR
command and uses a proprietary
halfduplex protocol; default DM rate
fixed at 115200 bps
mobile’s serial port to DM mode; DM
mode runs at rate set by $QCDMR
command and uses a proprietary
halfduplex protocol; default DM rate
fixed at 115200 bps
Supported
$QCDMR=
<rate>
<rate>
set DM baud rate
Changes DM rate that will be used on
mobile’s serial port when mobile’s
serial port transitions to DM mode; DM
mode is entered after $QCDMG
command is issued; default DM rate is
fixed at 115200 bps; test command,
i.e., $QCDMR=?, returns rates
supported and query command, i.e.,
$QCDMR?, returns current
Rate
mobile’s serial port when mobile’s
serial port transitions to DM mode; DM
mode is entered after $QCDMG
command is issued; default DM rate is
fixed at 115200 bps; test command,
i.e., $QCDMR=?, returns rates
supported and query command, i.e.,
$QCDMR?, returns current
Rate
Supported
&V
dump configuration
parameters
parameters
Dumps the status of all AT parameters
applicable to current operating mode,
including the single-letter parameters
not otherwise readable
applicable to current operating mode,
including the single-letter parameters
not otherwise readable
Supported
&C2
Circuit 109 (carrier
detect pin) behavior -
wink
detect pin) behavior -
wink
Setting “winks” (briefly transitions off,
then back on) the Rm port Carrier
Detect pin when Data calls end
then back on) the Rm port Carrier
Detect pin when Data calls end
Supported
$QCTER=
<rate>
<rate>
Set TE-DCE baud rate
Baud rates supported
are identical to +IPR
command.
Baud rates supported
are identical to +IPR
command.
Sets TE-DCE rate at which DCE will
accept commands; this data rate also
becomes the default and is stored in
NV RAM, changing the +IPR
command default rate; test command,
i.e., $QCTER=?, returns rates
supported and query command, i.e.,
$QCTER?, returns rate last issued by
$QCTER command or default rate
accept commands; this data rate also
becomes the default and is stored in
NV RAM, changing the +IPR
command default rate; test command,
i.e., $QCTER=?, returns rates
supported and query command, i.e.,
$QCTER?, returns rate last issued by
$QCTER command or default rate
Supported
$ $QCDNSP=
<address>
<address>
set primary DNS IP address
Sets the default primary IP address
used for Domain Name Services;
used only if no DNS server address is
received over the air during PDP
context activation; value is stored in
NVRAM.
used for Domain Name Services;
used only if no DNS server address is
received over the air during PDP
context activation; value is stored in
NVRAM.
Supported
$QCDNSS=
<address>
<address>
Set secondary DNS IP
address
address
Sets the default secondary IP address
used for Domain Name Services;
used only if no DNS server address is
received over the air during PDP
context activation; value is stored in
NVRAM
used for Domain Name Services;
used only if no DNS server address is
received over the air during PDP
context activation; value is stored in
NVRAM
Supported
$QCPDPP=
<cid>,
<auth_type>,
<cid>,
<auth_type>,
PDP-IP packet data calls
<cid> – 1 to 16
<auth_type>:
<cid> – 1 to 16
<auth_type>:
Defines authentication parameters on
a per connection basis. Value of
<auth_type> determines what
a per connection basis. Value of
<auth_type> determines what
Supported