Murphy S10 Series Leaflet
S10 series
AUTOMATIC BATTERY CHARGERS
RATINGS TO 10 AMPS
RATINGS TO 10 AMPS
The S10 is a constant potential, open-chassis battery
charger, suitable for use with either 12V DC or 24V DC,
lead acid or Ni-Cd systems. Although primarily designed
for the diesel generator market, the charger may be
configured for use in a wide range of unattended industrial
applications where standby power is required at all times.
charger, suitable for use with either 12V DC or 24V DC,
lead acid or Ni-Cd systems. Although primarily designed
for the diesel generator market, the charger may be
configured for use in a wide range of unattended industrial
applications where standby power is required at all times.
Each unit consists of a transformer, rectifier and control
circuitry. The charger monitors the battery voltage and
delivers as much current as the cells require up to the
current limited maximum, giving a rapid recovery of charge.
Once the battery is fully charged, the charger provides a
low trickle charge to maintain the cells for an indefinite
period at a pre-set float voltage, without overcharging, plus
any additional current required to support a static load.
circuitry. The charger monitors the battery voltage and
delivers as much current as the cells require up to the
current limited maximum, giving a rapid recovery of charge.
Once the battery is fully charged, the charger provides a
low trickle charge to maintain the cells for an indefinite
period at a pre-set float voltage, without overcharging, plus
any additional current required to support a static load.
Also included is a range of on-board fault monitors
complete with volt free relay contacts for remote
alarm signalling.
complete with volt free relay contacts for remote
alarm signalling.
Standard Features
•
Boost function, operated by remote link.
Indication by amber LED.
Indication by amber LED.
•
Adjustable float and boost voltage levels to meet with
a range of battery types, static loads and operating
conditions. Standard calibrations are:-
a range of battery types, static loads and operating
conditions. Standard calibrations are:-
BATTERY TYPE
FLOAT
VOLTAGE
(V DC)
BOOST
VOLTAGE
(VDC)
Lead acid (6 cells)
13.6
14.1
12 V
Ni-Cd (9 cells)
12.8
14.0
Ni-Cd (10 cells)
14.2
15.6
Lead acid (12 cells)
27.2
28.4
24 V
Ni-Cd (18 cells)
25.6
28.1
Ni-Cd (20 cells)
28.4
31.2
•
Adjustable current limit. Standard versions have a
10 Amp limit, but this may be adjusted downwards
where required (e.g. for lower capacity batteries).
10 Amp limit, but this may be adjusted downwards
where required (e.g. for lower capacity batteries).
•
Output short circuit protection.
•
Protection against reverse polarity battery connection
via fuse and red warning LED.
via fuse and red warning LED.
•
3 alarm monitoring circuits: 'charge fail', 'low battery
voltage' and 'high battery voltage', complete with
volt-free relay outputs and LED indicators. The low
battery voltage alarm features a fixed time delay of
approx. 60 secs. to inhibit the signalling of a fault
during normal battery loading (e.g. engine cranking).
voltage' and 'high battery voltage', complete with
volt-free relay outputs and LED indicators. The low
battery voltage alarm features a fixed time delay of
approx. 60 secs. to inhibit the signalling of a fault
during normal battery loading (e.g. engine cranking).
Electrical connection of the battery, boost and charge
monitoring relays is via ¼" blade terminals. The AC supply
is connected through separately mounted screw terminals.
monitoring relays is via ¼" blade terminals. The AC supply
is connected through separately mounted screw terminals.
When ordering, please specify:-
a) Product type (S10 series)
b) Nominal output voltage (12 or 24 V DC)
c)
b) Nominal output voltage (12 or 24 V DC)
c)
AC supply voltage (240 or 110 V)
d) Battery type (Lead-acid, or Ni-Cd and number of cells,
or special calibration requirements).
The Generator Controls Division of
R
M020301
Issue 5, revised 07/98
Catalogue section 75
Dimensions (mm)
Overall
Fixing Base
Connection
L
4
2
5 6
7
8
3
1
F1
S1012, 240V: 1.5A
110V: 3.15A
S1024, 240V: 3.15A
110V: 6.3A
110V: 3.15A
S1024, 240V: 3.15A
110V: 6.3A
F1, fuse type T, rating:
AC
supply
N
Boost
switch/timer
switch/timer
E
10
9
BCS
battery
charge
fail
high
battery
volts
low
battery
volts
+
–
Product Specification
Power supply:
operating voltages
240 V AC or 110 V AC (specify),
+/– 10%, 50/60 Hz.
Charging output:
nominal output voltage
see chart left
voltage stability
+/– 1% of nominal
current limit
1 – 10 Amps, factory set
current stability
+/– 2% of nominal
Relay outputs:
(ratings for resistive load)
charge fail and low battery volts
high battery volts
volt free SPNC contacts
volt free SPNO contacts
all rated 5 A @ 30 V DC
General:
operating temperature
–10 to +55
o
C
overall dimensions (h x l x d)
185 x 145 x 155 mm
weight
approx. 8.0 Kg
EMC emission/immunity
to EN50081-2/EN50082-2
Since 1939
Frank W. Murphy Manufacturer
PO Box 470248, Tulsa, Oklahoma 74147, USA
Tel: + 1 918 627 3550 Fax: + 1 918 664 6146
email: sales@fwmurphy.com
web: http://www.fwmurphy.com
Frank W. Murphy Southern Division
PO Box 1819, Rosenberg, Texas 77471, USA
Tel: + 1 281 342 0297 Fax: + 1 281 341 6006
email: sales@fwmurphy.com
Frank W. Murphy Ltd.
Incorporating
Modex Automation
Church Road, Laverstock, Salisbury U.K.
Tel: + 44 1722 410055 Fax + 44 1722 410088
Pour service en Français, tél: + 44 1722 410697
email: sales@fwmurphy.co.uk
web: http://www.fwmurphy.co.uk
Murphek Pty. Ltd.
1620 Hume Highway, Campbellfield, Vic. 3061 Australia
Tel: + 61 3 9358 5555 Fax: + 61 3 9358 5558
email: murphy@macquarrie.com.au
Murphy Switch of California
PO Box 900788, Palmdale, California 93590, USA
Tel: + 1 805 272 4700 Fax: + 1 805 947 7570
email: sales@murphyswitch.com
web: http://www.murphyswitch.com
Murphy de Mexico S.A. de C.V.
Blvd. Antonio Rocha Cordero 300, Fracción del Aguaje
San Luis Potosí, S.L.P. México 78384
Tel: + 52 48 206264 Fax: + 52 48 206336
email: murmexsl@sanluis.podernet.com.mx
Frank W. Murphy Pte, Ltd.
No. 2 Tuas South Street 2, Sprintecs Building
02-01/02, Singapore 637895
Tel: + 65 863 1398 Fax: + 65 863 0208
email: fwmsales@fwmurphy.com.sg
Frank W. Murphy Ltd. en France
Tel: +33 (1) 30 76 26 26 Fax: +33 (1) 30 76 39 89
Direct usine Tel: + 44 1722 410697
email: sales@fwmurphy.co.uk