Philips AZ1305/17 User Manual

Enregistrez votre produit
dans les 10 jours pour
confirmer votre droit à
une protection maximum
selon les termes et les
conditions de votre
garantie Philips.

Votre carte d’enreg-
istrement de garantie
prouve que vous possédez
l’appareil en cas de vol ou
de perte du produit.

Renvoyez votre carte d’en-
registrement de garantie dès
aujourd’hui pour vous assur-
er de recevoir toutes les
informations, les offres et les
bonus auxquels vous avez
droit en tant que possesseur
de ce modèle.

Cet « éclair à pointe de
flèche » indique qu’un matéri-
au non isolé, situé à l’intérieur

de l’unité, risque de provoquer un choc
électrique. Pour la sécurité de chacun,
nous vous prions de ne pas retirer le
boîtier de ce produit.

Le « point d’exclamation »
attire votre attention sur des
sujets risquant de provoquer

des problèmes de fonctionnement et
d’entretien si vous ne lisez pas les infor-
mations s’y reportant.

NE PAS EXPOSER

CET ÉQUIPEMENT A LA PLUIE NI A
UNE HUMIDITÉ EXCESSIVE POUR
ÉVITER LES RISQUES D’INCENDIE
ET DE CHOC ÉLECTRIQUE.

Pour éviter les

chocs électriques, introduire la lame la
plus large de la fiche dans la borne
correspondante de la prise et pousser
jusqu’au fond.

Cet espace vous est réservé
Inscrivez ci-dessous le numéro de série situé
à l’arrière du bloc. Conservez cette informa-
tion pour vous y reporter à l’avenir.

N

°

de modèle  ____________________

N

°

de série  ______________________

MAC5097

Registre su producto den-
tro de 10 días para confir-
mar su derecho a máxima
protección bajo los térmi-
nos y condiciones de la
garantía de Philips.

Su Tarjeta de Registro de
la Garantía comprueba
que Ud. es el dueño del
aparato en caso de robo
o pérdida del producto.

La devolución inmediata de
su Tarjeta de Registro de la
Garantía le garantiza que
recibirá toda la información
y todas las promociones
especiales que le corre-
sponden por ser el dueño
de su modelo.

El símbolo del «rayo» indica
que algún material no aislado
dentro de su unidad podría

resultar en una sacudida eléctrica. Para
la seguridad de todos, favor de no
remover la cubierta del producto.

El «signo de exclamación» le
llama la atención a carac-
terísticas sobre las que Ud.

debe leer la información adjunta
detenidamente para evitar problemas
de funcionamiento y mantenimiento.

PARA EVI-

TAR EL RIESGO DE SACUDIDA
ELECTRICA O INCENDIO, NO
EXPONGA ESTE EQUIPO A LLUVIA
NI A  HUMEDAD.

Para evitar

sacudida eléctrica, introduzca la patilla
ancha del enchufe al fondo de la ranu-
ra ancha.

Para uso del cliente:
Escriba abajo el número de serie que se
encuentra en el panel posterior. Guarde
esta información para el futuro.

No. de modelo ____________________

No. de serie  ______________________

MAC5097

Registering your product
within 10 days confirms
your right to maximum
protection under the
terms and conditions of
your Philips warranty.

Your completed Warranty
Registration Card serves
as verification of owner-
ship in the event of prod-
uct theft or loss.

Returning your Warranty
Registration Card right
away guarantees you’ll
receive all the information
and special offers which
you qualify for as the
owner of your model.

This “bolt of lightning” indi-
cates uninsulated material
within your unit may cause

an electrical shock. For the safety of
everyone in your household, please do
not remove product covering.

The “exclamation point” calls
attention to features for
which you should read the

enclosed literature closely to prevent
operating and maintenance problems.

TO PREVENT

FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.

To prevent electric

shock, match wide blade of plug to
wide slot, and fully insert.

For Customer Use
Enter below the Serial No. which is locat-
ed on the rear of the cabinet. Retain this
information for future reference.

Model No. _______________________

Serial No. ________________________

MAC5097

This symbol indicates that the unit has a double insulation system.

Este símbolo indica que la unidad tiene un sistema doble de aislamiento.

Ce symbole indique que l’appareil est équipé d’un système à double isolation.

de calor – Como radiadores, calentadores,
estufas o cualquier otro aparato (incluyen-
do los amplificadores) generador de calor.

seguridad de la
clavija de corriente
(ya sea de tipo polar-
izado o 
con toma de tierra). Las clavijas polarizadas
tienen dos patillas, una más ancha que la
otra. Las que disponen de toma de tierra
tienen dos patillas y una tercera que es la
de conexión a tierra.Tanto la patilla más
ancha como la toma de tierra han sido
incorporadas a la clavija para su seguridad
personal. Si la clavija suministrada con el
equipo no es compatible con su toma de
corriente, consulte a un electricista para
sustituir la toma de corriente obsoleta.

diendo que pueda pisarse o incluso per-
forarse, especialmente en la parte más
próxima a la clavija y en el punto de salida
del equipo.

positivos/ accesorios recomendados
por el fabricante.

Coloque el equipo exclusi-
vamente sobre aquellos carros,
bases, trípodes, soportes o
mesas especificados por el com-
erciante o vendidos con el
equipo. Cuando utilice un carro,
tenga cuidado al desplazar el
conjunto carro/ equipo para evi-
tar posibles daños por vuelco.

13. Desenchufe el aparato durante tor-

mentas eléctricas o cuando no vaya a ser
utilizado durante largo tiempo.

reparaciones a personal técnico especial-
izado. El equipo deberá repararse siempre
que haya resultado dañado de alguna man-
era, como por ejemplo por daños en el
cable o en la clavija, por derrame de líqui-
do sobre el equipo, por objetos que
hubieran podido introducirse en su interior,
por exposición del equipo a la lluvia o a
ambientes húmedos, cuando el equipo no
funcione con normalidad o cuando hubiera
sufrido algún tipo de caída.

15. Uso de las pilas – ADVERTENCIA: Para

prevenir escapes en las pilas, que pueden
ocasionar lesiones físicas, daños a
su propiedad o dañar la unidad:

● Instale todas las pilas correctamente, + y -

como está marcado en la unidad.

● No mezcle las pilas (viejas con nuevas o

de carbono y alcalinas, etc.).

● Extraiga las pilas cuando no vaya a usar la

unidad durante largo tiempo.

In the stop position, select and store your CD tracks in

the desired sequence. Up to 20 tracks can be stored in

the memory.

1. Press SEARCH 

∞ or § on the set to select your

desired track number.

2. Press PROG.

™ Display: PROG, Prog briefly and your 

selected track number. (See 5)

™ If you attempt to program without first 

selecting a track number, noSE is shown.

3. Repeat steps 1-2 to select and store all desired

tracks.

™ Display: FULL if you try to program more

than 20 tracks.

In the stop position, press and hold PROG until the

display shows all your stored track numbers in

sequence.

You can erase the program by either:

• pressing 

9 twice

™ CLr is displayed briefly and PROG

disappears.

• You select AM / FM function.

• Open the CD door.

SAFETY & MAINTENANCE INFORMATION 
(See 7)

• Don't expose the set, batteries, CDs to humidity,

rain, sand or excessive heat.

• Clean the set with a dry cloth. Don't use any 

cleaning agents containing alcohol, ammonia, 

benzene or abrasives as these may harm the set.

• Place the set on a hard and flat surface so that the

system does not tilt. Make sure there is good 

ventilation to prevent the set overheating.

• The mechanical parts of the set contain 

self-lubricating bearings and must not be oiled or

lubricated.

• If the CD player cannot read CDs correctly, use a

cleaning CD to clean the lens before taking the set

to repair.

• The lens of the CD player should never be touched!

• Sudden changes in the surrounding temperature

can cause condensation on the lens of your CD

player. Playing a CD is then not possible. Do not

attempt to clean the lens but leave the set in a

warm environment until the moisture evaporates.

• Always close the CD door to avoid dust on the lens.

• To clean the CD, wipe in a straight line from the

center towards the edge using a soft, lint-free

cloth. Do not use cleaning agents as they may

damage the disc.

• Never write on a CD or attach any stickers to it.

– Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries drained/ incorrectly inserted
• Insert (fresh) batteries correctly

– Electrical interference: set too close to TV, VCR or

• Move the set to increase the distance

– Weak radio signal
• FM: Adjust the FM telescopic antenna

nocd indication

– CD badly scratched or dirty
• Replace/ clean CD, see Maintenance
– Laser lens steamed up
• Wait until lens has cleared

nFcd indication

– CD-R(W) is blank/ not finalized
• Use a finalized CD-R(W)

dAtA indication

– CD contains non-audio files
• Press SEARCH 

∞ or § once or more to skip to a

CD audio track, instead of the data file

– CD damaged or dirty
• Replace or clean CD
– SHUFFLE or PROG is active
• Switch off SHUFFLE / PROG

– Batteries exhausted/ incorrectly inserted
• Insert (fresh) batteries correctly
– Distance/ angle between the set too large
• Reduce the distance/ angle

such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.

the safety 
purpose of the
polarized or 
grounding-type plug. A polarized plug has
two blades with one wider than the other.
A grounding type plug has two blades and
a third grounding prong.The wide blade or
the third prong are provided for your safe-
ty. If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being

walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.

specified by the manufacturer.

Use only with the cart,
stand, tripod, bracket, or table
specified by the manufacturer or
sold with the apparatus. When a
cart is used, use caution when
moving the cart/apparatus com-
bination to avoid injury from
tip-over.

13. Unplug this apparatus during lightning

storms or when unused for long periods of
time.

14. Refer all servicing to qualified service

personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is dam-
aged, liquid has been spilled or objects
have fallen into the apparatus, the appara-
tus has been exposed to rain or moisture,
does not operate normally, or has been
dropped.

15. Battery usage CAUTION – To  prevent

battery leakage which may result in bodily
injury, property damage, or damage to the
unit:

● Install all batteries correctly, + and - as

marked on the unit.

● Do not mix batteries (old and new or

carbon and alkaline, etc.).

● Remove batteries when the unit is not

used for a long time.

1 x AC power cord

1 x Remote Control (for AZ1305 model only)

TOP AND FRONT PANEL (See 1)

1 LIFT TO OPEN - lift here to open CD door.

2 PROG

CD: - programs tracks and reviews the program;

Tuner: - programs preset radio stations.

3 MODE - selects different play modes: e.g. REPEAT

or SHUFFLE (random) order.

4 VOLUME 

3 , 4 - to adjust volume level.

,

(up, down) - selects a preset radio 

station.

5 Display - shows the status of the set.

6

2; - starts or pauses CD playback.
9 - to stop playback or erase a CD program.
SEARCH

∞ , §

CD: - searches backward and forward within a track;

- skips to the beginning of a current track/ 

previous/ later track.

RADIO: - (down, up) tunes to radio stations.

7 DBB (Dynamic Bass Boost) - activates a more vivid

bass response.

8 POWER slider - selects CD/ AM / FM / OFF

function and also the power off switch (OFF).

BACK PANEL (See 1)

9 Telescopic antenna - improves FM reception.

0 Battery compartment - for 6 batteries, type 

R-14, UM2 or C-cells.

! AC MAINS - inlet for power cord.

1 VOLUME 

3 , 4 - adjusts volume level.

2 SHUFFLE - plays all CD tracks in random order.

3

2; - starts or pauses CD playback.

4 SEARCH 

5 , 6 - searches backwards/ 

forwards within a track.

5 PRESET

,

(up, down) - selects a preset radio 

station.

6 TUNING 

∞ , § (down, up) - tunes to tuner stations.

7

9 - to stop playback;

- erases a CD program.

8

¡ , ™ - skips to the beginning of a current track 
previous/ subsequent track.

9 REPEAT - repeats a track /program/ entire CD.

Whenever convenient, use the AC power supply to

conserve battery life. Make sure you remove the

power plug from the set and wall outlet before 

inserting batteries.

• Insert 6 batteries, type R-14, UM-2 or C-cells, 

(preferably alkaline) with the correct polarity. (See 6)

• Remote control (AZ1305 model only)

Insert 2 batteries, type AAA, R03 or UM4

(preferably alkaline). (See 8)

• Incorrect use of batteries can cause electrolyte 

leakage and will corrode the compartment or cause

the batteries to burst. 

• Do not mix battery types: e.g. alkaline with carbon

zinc. Only use batteries of the same type for the

set.

• When inserting new batteries, do not try to mix old

batteries with the new ones.

• Batteries contain chemical substances, so

1. Check if the AC power supply, as shown on the

corresponds to your local power supply. If it does

not, consult your dealer or service center.

2. Connect the power cord to the outlet.

3. To disconnect the power supply, unplug the set

from the outlet.

1. To switch on, adjust the POWER slider to select:

CD, AM, FM function, and operate the respective

function controls.

2. To switch off, adjust the POWER slider to select

OFF .

Adjusting volume and sound (See 2)

1. Adjust the volume with the VOLUME controls.

™ Display shows the volume level in number from

0-32.

2. Press DBB once or more to select dynamic bass

boost on or off.

™ Display: shows 

when activated.

chaleur comme par exemple des radiateurs, bouches

de chaleur, cuisinières, ou autres appareils (même des

amplificateurs) dégageant de la chaleur.

Ne détruisez pas la sécurité incorporée dans la

prise de terre ou prise

polarisée fournie. Une 

prise polarisée est dotée de

deux lames 

dont une plus large que l’autre. Une prise de terre est

dotée de deux fiches semblables et d’une troisième,

plus large, qui assure la mise à la terre pour votre

sécurité. Si la prise fournie ne convient pas à la prise

murale dont vous disposez, consultez un électricien

pour remplacer et adapter votre prise murale.

10. Protégez le cordon d’alimentation pour éviter

de marcher dessus ou de le pincer particulièrement

aux endroits des prises, mâles et femelles, et au point

de raccordement sur l’appareil lui-même.

options recommandés par le fabricant.

sur roulettes, un support, un pied, une

étagère ou une table de type recom-

mandé par le fabricant. Si vous utilisez un

meuble sur roulettes, veillez à le déplacer

avec précaution afin d’éviter tout acci-

dent corporel si l’équipement se renver-

sait.

13. Débranchez l’appareil pendant les orages ou s’il

doit rester inutilisé pendant une période de temps

prolongée.

14. Pour toute réparation, faites appel à un personnel

qualifié. Une réparation sera nécessaire si l’appareil a

subi des dommages tels que détérioration du cordon

d’alimentation ou de la prise, liquide renversé sur l’ap-

pareil, ou encore si un objet est tombé dessus, si l’ap-

pareil a été exposé à la pluie ou à l’humidité, s’il ne

fonctionne pas correctement ou s’il a fait une chute.

15. PRÉCAUTION d’emploi des piles – Afin d’éviter

toute fuite des piles qui risquerait de causer des

blessures corporelles, des dommages matériels, ou

d’endommager l’appareil :

●

Installez toutes les piles correctement, + et - tels

qu’indiqués sur l’appareil.

●

Ne mélangez pas les piles (pas de piles neuves avec

des usagées ou de piles au carbone avec des alca-

lines, etc.).

●

Enlevez les piles lorsque l’appareil reste inutilisé pen-

dant une longue période.

1. Adjust the POWER slider to AM or FM.

™ The radio station frequency, waveband are

shown (See 3)

2. Press and hold SEARCH

∞ or § until the 

frequency in the display starts running.

™ The radio automatically tunes to a station of

sufficient reception. Display shows Srch

during automatic tuning.

3. Repeat step 2 if necessary until you find the

desired station.

• To tune to a weak station, press 

∞ or § briefly

and repeatedly until you have found optimal 

reception.

• For FM, extend, incline and turn the telescopic

antenna. Reduce its length if the signal is too

strong.

• For AM , the set uses a built-in antenna. Direct this

antenna by turning the whole set.

You can store up to a total of 30 radio stations (20 FM

and 10 AM) in the memory, manually or automatically

(Autostore).

1. Tune to your desired station (see Tuning to radio

stations).

2. Press PROG to activate programming.

™ PROG flashes.

3. Press PRESET

/ 

once or more to select a 

preset number.

• Remote control (AZ1305 models only): Press

/ 

once or more to select a preset 

station.

4. Press PROG to confirm.

5. Repeat steps 1-4 to store other stations.

Autostore automatically starts programming radio 

stations from preset 1. Available stations are 

programmed in order if the station with sufficient

reception strength. Any previous presets e.g. manually

programmed will be erased.

• Press PROG for 2 seconds or more to activate

autostore programming.

™ The display shows AUtO, PROG blinks, 

followed by the radio station details when

stored.

After all stations are stored, the first preset station

will then automatically play.

• Press the PRESET

,

buttons once or more until

the desired preset station is displayed.

• Remote control (AZ1305 models only): optionally,

press PRESET

,

to select your preset station.

This CD player plays Audio Discs including CD-

Recordables and CD-Rewritables.

1. Adjust the POWER slider to CD.

2. Open the CD Door.

™ OPEN is displayed.

3. Insert a CD with the printed side facing up and

close the door.

™ nocd if no CD inserted/ CD dirty, incorrectly

inserted or damaged.

™ nFcd if you have inserted a non-finalized CD-

R(W).

4. Press 

2; to start playback.

™ dAtA if your CD contains non-audio i.e. data

files.

5. To pause playback press 

2;. Press 2; again to

resume play.

™ Display: 

1 flashes during pause.

6. To stop CD playback, press the 

9 button.

• Press SEARCH 

∞ or § once or repeatedly to 

select your track.

• In the pause / stop position, press 

2; to start 

playback.

1. Press and hold SEARCH 

∞ or §.

– The CD is played at high speed and low volume.

2. When you recognize the passage you want,

release 

∞ or § to resume normal playback.

You can select and change the various play modes

before or during playback, and combine the modes

with PROG. (See 4)

(SHUFFLE) - tracks of the entire CD/ program 

are played in random order

(SHUFFLE REPEAT ALL) - to repeat the 

entire CD/ program continuously in random order

(REPEAT ALL) - repeats the entire CD/ 

program

(REPEAT) - plays the current track continuously

1. To select play mode, press MODE once or more.

2. Press 

2; to start playback if in the stop position.

3. To select normal playback, press MODE

repeatedly until the various modes are no longer

displayed.

– You can also press the 

9 button to cancel your

play mode.

Knoxville, Tennessee 37914-1810, U.S.A.

Printed in China

W

AZ 1300
AZ 1305

Environmental information
We have done our best to reduce the packaging and make it easy to separate into 3 materials:
cardboard, expandable polystyrene, polyethylene.

If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service center.

English:This digital apparatus does not exceed the Class B limits for radio noise emis-
sions from digital apparatus as set out in the Radio Interference Regulations of the Cana-
dian Department of Communications.

Français: Cet appareil numérique n'émet pas de bruits radioélectriques dépassant les 
limites applicables aux appareils numériques de Classe B prescrites dans le Règlement sur
le Brouillage Radioélectrique édicté par le Ministère des Communications du Canada.

One Year  Free  Exchange

This product must be carried in for an exchange.

WHO IS COVERED?
You must have proof of purchase to exchange the product.
A sales receipt or other document showing that you pur-
chased the product is considered proof of purchase. Attach
it to this owner’s manual and keep both nearby.

WHAT IS COVERED?
Warranty coverage begins the day you buy your product.
For one year thereafter, a defective or inoperative product
will be replaced with a new, renewed or comparable prod-
uct at no charge to you. A replacement product is covered
only for the original warranty period.When the warranty
on the original product expires, the warranty on the
replacement product also expires.

WHAT IS EXCLUDED?
Your warranty does not cover:
•

labor charges for installation or setup of the product,
adjustment of customer controls on the product, and
installation or repair of antenna systems outside of the
product.

•

product repair and/or part replacement because of
misuse, accident, unauthorized repair or other cause
not within the control of Philips.

•

reception problems caused by signal conditions or
cable or antenna systems outside the unit.

•

a product that requires modification or adaptation to
enable it to operate in any country other than the
country for which it was designed, manufactured,
approved and/or authorized, or repair of products
damaged by these modifications.

•

incidental or consequential damages resulting from the
product. (Some states do not allow the exclusion of
incidental or consequential damages, so the above
exclusion may not apply to you.This includes, but is not
limited to, prerecorded material, whether copyrighted
or not copyrighted.)

•

a product used for commercial or institutional purposes.

WHERE IS EXCHANGE AVAILABLE?
You may exchange the product in all countries where the
product is officially distributed by Philips. In countries
where Philips does not distribute the product, the local
Philips service organization will attempt to provide a
replacement product (although there may be a delay if the
appropriate product is not readily available).

BEFORE REQUESTING EXCHANGE...
Please check your owner's manual for assistance. If you
have additional questions, call us at 1-800-531-0039.

EXCHANGING A  PRODUCT  IN  U.S.A.,
PUERTO RICO, OR U.S.VIRGIN ISLANDS...
Contact 1-800-531-0039 to arrange an exchange. Or, ship
the product, insured and freight prepaid, and with proof of
purchase enclosed, to the address listed below.

Philips Exchange Program

Suite A

406 North Irish Street

Greeneville TN  37745

(In U.S.A., Puerto Rico, and U.S.Virgin Islands, all implied war-
ranties, including implied warranties of merchantability and fit-
ness for a particular purpose, are limited in duration to the
duration of this express warranty. But, because some states do
not allow limitations on how long an implied warranty may
last, this limitation may not apply to you.)

EXCHANGING A PRODUCT IN CANADA...
Please contact Philips at:

1-800-661-6162 (French Speaking)

1-800-531-0039 (English or Spanish Speaking)

(In Canada, this warranty is given in lieu of all other war-
ranties. No other warranties are expressed or implied,
including any implied warranties of merchantability or fit-
ness for a particular purpose. Philips is not liable under any
circumstances for any direct, indirect, special, incidental or
consequential damages, howsoever incurred, even if notified
of the possibility of such damages.)

REMEMBER...
Please record below the model and serial numbers found
on the product. Also, please fill out and mail your warranty
registration card promptly. It will be easier for us to notify
you if necessary.

MODEL #

__________________________________

SERIAL #

__________________________________

EL6095T004 / 8-02

VOLUME

SEARCH

PRESET

TUNING

REPEAT

SHUFFLE

SEARCH

1

9

8

6

7

2

4

3

5

1

2

3

4

5

6

7

8

AC M

AINS ~

!

0

9

1

2

3

4

5

8

7

6

AZ1300/17  2/12/02  12:46  Page 1