Alliance Laundry Systems SFG109*F User Manual
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Installation
9
510977
Before You Start
Tools
For most installations, the basic tools you will need
are:
are:
Figure 3
NOTE: An 8 in. (20.32 cm) coin drawer is required
for coin operated MDC and NetMaster models.
for coin operated MDC and NetMaster models.
Installing the Dryer
Step 1: Position and Level the Dryer
Install dryer before washer. This allows room for
attaching exhaust duct.
attaching exhaust duct.
Install the four rubber feet (in accessories bag).
Select a location with a solid floor. Dryers installed in
residential garages must be elevated 18 inches (46 cm)
above the floor.
residential garages must be elevated 18 inches (46 cm)
above the floor.
No other fuel burning appliance should be installed in
the same closet with the dryer.
the same closet with the dryer.
The dryer must not be installed or stored in an area
where it will be exposed to water and/or weather.
where it will be exposed to water and/or weather.
The dryer needs sufficient clearance and an adequate
air supply for proper operation and ventilation, and for
easier installation and servicing. (Minimum clearances
are shown in Figure 4).
air supply for proper operation and ventilation, and for
easier installation and servicing. (Minimum clearances
are shown in Figure 4).
Place the dryer in position, and adjust the legs until the
dryer is level from side to side and front to back.
Leveling legs can be adjusted from inside the dryer
with a 1/4 in. driver. All four legs must rest firmly on
the floor so the weight of the dryer is evenly
distributed. The dryer must not rock.
dryer is level from side to side and front to back.
Leveling legs can be adjusted from inside the dryer
with a 1/4 in. driver. All four legs must rest firmly on
the floor so the weight of the dryer is evenly
distributed. The dryer must not rock.
Figure 4
IMPORTANT: In mobile home installations, gas
dryers MUST be permanently attached to the floor
at the time of installation. Order No. 526P3 Hold
Down Kit (available at extra cost) for a
manufactured (mobile) home installation. Follow
the instructions supplied with the kit.
dryers MUST be permanently attached to the floor
at the time of installation. Order No. 526P3 Hold
Down Kit (available at extra cost) for a
manufactured (mobile) home installation. Follow
the instructions supplied with the kit.
Installation of unit must conform to the Manufactured
Home Construction and Safety Standards, Title 24
CF4, Part 32-80 or Standard CAN/CSA-Z240 MH.
Home Construction and Safety Standards, Title 24
CF4, Part 32-80 or Standard CAN/CSA-Z240 MH.
D818I
1
Wrench
2
Screwdrivers
3
Level
4
Teflon Tape
5
Duct Tape
1
2
3
4
5
Any disassembly requiring the use of
tools must be performed by a suitably
qualified service person.
tools must be performed by a suitably
qualified service person.
W299
WARNING
D710I
1
Dryer Base
2
Leveling Leg
3
Level
4
Rubber Cup
IN US
E
PERM
PRES
S
NORM
AL
FLUFF
(NO H
(NO H
EAT)
DELIC
ATE
PUSH
TO S
TART
FABR
IC SE
LECT
OR
50421
0
OPER
ATING
INST
RUCT
IONS
CLEAN LIN
T FILTER
AFTER
EAC
H LOA
D
1.
2.
3.
4.
5.
6.
Select
Fabric
Type (h
eat sett
ing)
N
ORMA
L, PER
M PRE
SS,
D
ELICAT
E, FLU
FF (no
heat)
Load C
lothes.
Insert C
oin(s)/C
ard.
To Sta
rt Drye
r - Clos
e Door
and Pu
sh Star
t.
To Sto
p Drye
r Durin
g Cycle
- Open
Door.
To Res
tart Dry
er - Clo
se Doo
r and P
ush Sta
rt.
Drying C
ycle is
Comple
te Whe
n
Panel L
ight Go
es Off.
D710I
3
2
1
4