Alliance Laundry Systems 250 C.F.M. User Manual
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
M414545
59
D. Special Time Mode
This mode is just like the Time Dry mode, except
that the regulating temperature for each heat cycle
ranges from 80°F to 180°F. To enter the Special
Time mode, press the SPECIAL TIME pad after
selecting a cycle. The display will read “St:**”,
where “**” is the drying time. This time can be
changed by pressing the MORE or LESS pads.
For 1 minute changes, press the pad and release.
For 5 minute changes, press the pad and hold.
Maximum drying time allowed is 60 minutes.
that the regulating temperature for each heat cycle
ranges from 80°F to 180°F. To enter the Special
Time mode, press the SPECIAL TIME pad after
selecting a cycle. The display will read “St:**”,
where “**” is the drying time. This time can be
changed by pressing the MORE or LESS pads.
For 1 minute changes, press the pad and release.
For 5 minute changes, press the pad and hold.
Maximum drying time allowed is 60 minutes.
AC:** will be displayed when tumbler is in Auto
Cool Down. Typical cool down times for fabric
selections are preset. Refer to Table 9. The cool
down time can only be altered before cycle is
started. To alter cool down time press the COOL
DOWN pad and then press the MORE or LESS
pad (when cool down time is altered, TC:** will
be displayed). For 1 minute changes, press pad
and release. For 5 minute changes, press pad and
hold. Cooling time can be from 1 to 39 minutes.
To return to the Auto Cool Down, press MORE or
LESS pad until AC:** is displayed.
Cool Down. Typical cool down times for fabric
selections are preset. Refer to Table 9. The cool
down time can only be altered before cycle is
started. To alter cool down time press the COOL
DOWN pad and then press the MORE or LESS
pad (when cool down time is altered, TC:** will
be displayed). For 1 minute changes, press pad
and release. For 5 minute changes, press pad and
hold. Cooling time can be from 1 to 39 minutes.
To return to the Auto Cool Down, press MORE or
LESS pad until AC:** is displayed.
To start the cycle, press START. The total drying
time plus cool down time will display. During the
cycle, remaining time displays.
time plus cool down time will display. During the
cycle, remaining time displays.
E. Custom
Frequently used cycles can be saved in the
control’s memory as Custom cycles. Only one
cycle can be saved for each fabric type.
control’s memory as Custom cycles. Only one
cycle can be saved for each fabric type.
Create an Automatic, Time Dry, Special, or
Special Time cycle using instructions in section
4A, 4B, 4C or 4D. Save by pressing the word
CUSTOM before pressing START. To change a
Custom cycle, repeat above.
Special Time cycle using instructions in section
4A, 4B, 4C or 4D. Save by pressing the word
CUSTOM before pressing START. To change a
Custom cycle, repeat above.
To recall and use a Custom cycle, press its ON/
SELECT pad twice. Press START.
SELECT pad twice. Press START.
During Custom cycles the display is the same as
non-Custom Automatic cycles. The CUSTOM
status light will be on.
non-Custom Automatic cycles. The CUSTOM
status light will be on.
When creating or changing a Custom cycle,
record it on a Custom Cycle Record. Refer to
Figure 30. To modify or fine-tune a Custom cycle,
its values must be known. Custom cycle values
can be extracted from the micro-control, but it is
easier and more permanent to use the Custom
Cycle Record.
record it on a Custom Cycle Record. Refer to
Figure 30. To modify or fine-tune a Custom cycle,
its values must be known. Custom cycle values
can be extracted from the micro-control, but it is
easier and more permanent to use the Custom
Cycle Record.