Alliance Laundry Systems 504523R3 User Manual
504523
9
Dryer Slide Extension . . .
1. Assemble coin slide extension, No. 503733, to top
side of coin slide using two Phillips head screws and
lockwashers, No. 03950. Tighten firmly.
lockwashers, No. 03950. Tighten firmly.
2. Install slide extension modifier, No. 501796, as
follows:
NOTE: Dryers equipped with Greenwald coin slides
(except for Greenwald Comet Slide or Greenwald
Tokette Slide) do not require the use of the slide
extension modifier.
(except for Greenwald Comet Slide or Greenwald
Tokette Slide) do not require the use of the slide
extension modifier.
•
ESD Coin Slide – Mount slide extension
modifier, No. 501796, to the underside of slide
extension, No. 503733. Align the hole in the slide
extension modifier with hole “A” in the slide
extension and install self-tapping screw, No.
501086. Tighten firmly.
modifier, No. 501796, to the underside of slide
extension, No. 503733. Align the hole in the slide
extension modifier with hole “A” in the slide
extension and install self-tapping screw, No.
501086. Tighten firmly.
•
GREENWALD Comet Slide, GREENWALD
Tokette Slide or MONARCH Coin Slide –
Mount slide extension modifier, No. 501796, to
the underside of slide extension, No. 503733.
Align the hole in the slide extension modifier with
hole “B” in the slide extension and install self-
tapping screw, No. 501086. Tighten firmly.
Tokette Slide or MONARCH Coin Slide –
Mount slide extension modifier, No. 501796, to
the underside of slide extension, No. 503733.
Align the hole in the slide extension modifier with
hole “B” in the slide extension and install self-
tapping screw, No. 501086. Tighten firmly.
3. Reinstall coin slide in dryer meter case.
4. CHECK DRYER OPERATION – Connect electrical
power to dryer. Place required number of coins in
coin slide. Push slide in, and observe through service
door opening in meter case. The slide extension
should be contacting the accumulator actuator arm
and moving back with slide travel.
coin slide. Push slide in, and observe through service
door opening in meter case. The slide extension
should be contacting the accumulator actuator arm
and moving back with slide travel.
When slide is pushed all the way in, slide is retracted.
Accumulator actuator arm should remain back until
slide extension is moved forward and contacts
actuator arm agian, returning arm to starting position.
Accumulator actuator arm should remain back until
slide extension is moved forward and contacts
actuator arm agian, returning arm to starting position.
5. After completing the dryer check, reinstall service
door on top of meter case.
NOTE: When reinstalling service door, front of door
must be inserted at about a 45
must be inserted at about a 45
° angle in order to engage
notched tabs with internal rib at top of meter case.
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
WARNING
D019KE1C
COIN
SLIDE
03950
PHILLIPS
HEAD
SCREWS
AND
LOCKWASHERS
HOLE "B"
503733
SLIDE
EXTENSION
HOLE "A"
501796
SLIDE EXTENSION
MODIFIER
501086
SELF-TAPPING
SCREW
D044KE1A
ACCUMULATOR
ACTUATOR ARM
SLIDE
EXTENSION
MODIFIER
SLIDE
EXTENSION
COIN
SLIDE