Fujitsu MCE3064SS User Manual
C156-E097-01EN
7 - 21
If the TARG cannot detect a response from the INIT when the Selection Timeout Delay
(recommended: 250 ms) or longer has passed in the RESELECTION phase, the timeout
procedure shall be performed though one of the following schemes:
(recommended: 250 ms) or longer has passed in the RESELECTION phase, the timeout
procedure shall be performed though one of the following schemes:
1) The INIT asserts the RST signal to generate the RESET condition.
2) TARG terminates releasing SCSI ID to DATA BUS with maintaining SEL signal and I/O
signal in TRUE status. Subsequently, the INIT waits for the response from TARG for at
least 200
least 200
µ
s (Selection Abort Time) + 90 ns (Deskew Delay
×
2). If no response is detected,
the INIT releases the SEL signal allowing the SCSI bus to go to the BUS FREE phase. If the
INIT detects the reponse from TARG during this period, the INIT considers the
SELECTION phase to have completed normally.
INIT detects the reponse from TARG during this period, the INIT considers the
SELECTION phase to have completed normally.
The ODD performs process 2) above as RESELECTION-phase time-out processing.
7.5.5
INFORMATION TRANSFER phases
COMMAND, DATA, STATUS, and MESSAGE phases are generally called INFORMATION
TRANSFER phases. In these phases, data and control information are transferred between the
INIT and the TARG through the data bus.
TRANSFER phases. In these phases, data and control information are transferred between the
INIT and the TARG through the data bus.
The type of INFORMATION TRANSFER phase is determined by the combination of C/D, I/O,
and MSG signals (see Table 7.1). Since these three signals are specified by the TARG, phase
transition is controlled by the SCSI device operating as a TARG. The INIT can request the
TARG to initiate an MESSAGE OUT phase by sending an ATN signal. Besides, the TARG can
change the bus phase to BUS FREE by ceasing transmission of the BSY signal.
and MSG signals (see Table 7.1). Since these three signals are specified by the TARG, phase
transition is controlled by the SCSI device operating as a TARG. The INIT can request the
TARG to initiate an MESSAGE OUT phase by sending an ATN signal. Besides, the TARG can
change the bus phase to BUS FREE by ceasing transmission of the BSY signal.
Information transfer in an INFORMATION TRANSFER phase is controlled by REQ and ACK
signals. The REQ signal is sent by the TARG to request data transfer, and the ACK signal is a
response from the INIT. One pair of REQ and ACK signals causes one byte of information to be
transferred. According to the method of sending an REQ signal and checking the replied ACK
signal (REQ/ACK handshake), two data transfer modes are defined: synchronous and
asynchronous.
signals. The REQ signal is sent by the TARG to request data transfer, and the ACK signal is a
response from the INIT. One pair of REQ and ACK signals causes one byte of information to be
transferred. According to the method of sending an REQ signal and checking the replied ACK
signal (REQ/ACK handshake), two data transfer modes are defined: synchronous and
asynchronous.
During operation in an INFORMATION TRANSFER phase, the BSY signal must be kept true
by the TARG. The SEL signal must be false. The TARG must establish the status of three
signals C/D, I/O, and MSG which specify the phase type at least 400 ns (Bus Settle Delay)
before the leading edge of the REQ signal which requests transfer of the first byte. The TARG
must maintain that status until the trailing edge of the ACK signal corresponding to the last byte
in the phase (see Figure 7.9).
by the TARG. The SEL signal must be false. The TARG must establish the status of three
signals C/D, I/O, and MSG which specify the phase type at least 400 ns (Bus Settle Delay)
before the leading edge of the REQ signal which requests transfer of the first byte. The TARG
must maintain that status until the trailing edge of the ACK signal corresponding to the last byte
in the phase (see Figure 7.9).