Honeywell 9000 User Manual

INTELLIGUARD 9000™ SECURITY SYSTEM

74-3035—2

8003-280 Sensor

FEATURES
• Serial numbered device, no address switch setting

required.

• Learned through push button in conjunction with a

CC2 Keypad or using PRO9000. Button also enables

calibration mode.

• Completes calibration via the I9000 reset detector

command—unauthorized calibration causes alarm.

• Magnet assembly substitution detection (causes alarm

when polarity and field strength is out of calibrated

range).

• Status transmission (Door Open, Door Closed,

Calibration Failure).

Annunciation: Red LED communication status indicator visi-

ble through a slot in the cover.

Communication: RS-485 receiving and transmitting signals.

Enclosure: Plastic polycarbonate and aluminum (white).

Dimensions: 4-1/4 in. (108 mm) wide x 2-1/16 in. (52 mm)

high x 1-1/2 in. (39 mm) deep.

Weight: 0.4 lb (0.18 kg).

8003-282 Magnet Assembly

FEATURE
• To prevent substitution, calibration is lost when

Magnet Assembly is removed from mounted position.

Enclosure: Plastic polycarbonate.

Dimensions: 4-1/4 in. (108 mm) wide x 1-3/4 in. (45 mm)

high x 1-1/2 in. (39 mm) deep.

Weight: 2.88 oz (82g).

Other Detection and Alarm Devices

The I9000 accepts detection and output devices not described

in this specification. Any device added to the system must

conform to the specifications for the I9000. Talk to your

Honeywell representative for complete details.

Specifications

Detection Devices: Normally Open Dry Contacts Rated for

Switching: 18 Vdc at 1 mA to 100 mA.

Output Devices: Nominal 12 Vdc Devices: 9V to 18V

operating range at 1A maximum.

RS-232 to RS-485 Interface Assembly

The RS-232 to RS-485 Interface Assembly (RRI) is used to

convert the RS-232 signals from the CU COM 3 Port to RS-

485. This provides a means to connect the I9000 to the EBI

workstation via RS-485 ports, as well as allowing multi-drop

connections to other I9000 control units also equipped with an

RRI. Whether the EBI workstation is connected to a single

I9000 or multi-dropped to several I9000 control units, the

distance between units will be extended up to 3,277 ft (999m).

The distance is based on the assumption that the units are

extreme opposite devices with the longest cable length

between them, not the devices that are physically located the

farthest apart.

Features

• DIP switches enable RS-485 end-of-line termination

and line biasing.

Model: 8003-321 RS-232 to RS-485 Interface Assembly.

Electrical Ratings:

Nominal Operating Voltage: 12 Vdc to 15 Vdc.

Operating Voltage: 10 Vdc to 18 Vdc.

Operating Current: See Table 2.

Table 2. Operating Current.

NOTES:

— Use 22 AWG twisted pair cable for RS-485 connections.

For the RS-232 connections between the RRI and the ICP

II in the control unit enclosure, use solid 22 AWG wire

obtained from the twisted pair cable. Shielded cable is not

necessary because the wires are short and remain within

the control unit itself.

— For further details on RS-485 line termination and biasing,

refer to form no. 74-3047, Intelliguard 9000 Installation

Instructions.

Dimensions:

2-3/4 in. (70 mm) wide x 3-3/16 in. (81 mm) high x 1 in. (25

mm) deep.

Mounting:

Mounts to inside of I9000 Enclosure using 7003-217 Plastic

Track and 1041-004 Retaining Clip supplied with the RRI

Assembly.

Weight: 2 oz (57g).

Approvals: UL, ULC.

Multi-Drop Configurations

As many as three I9000 Control Units (Intelligent

Communications Processors (ICP-II) COM 3) can be

connected to an EBI workstation using the RRI and RS-485

bus wiring. The I9000 data is communicated to the central;

individual I9000s do not communicate peer-to-peer. Refer to

form no. 74-3047, Intelliguard 9000 Installation Instructions for

further details.

Connection Type

mA at 14.5V

Receiving (termination = enabled, bias

= disabled).

5.0

Single Unit Connection, Transmitting

(termination = enabled, bias = disabled).

36.2

Multi-drop Connection, Transmitting

(termination = disabled, bias =

disabled).

24.4