Home Automation SECURITY SYSTEM User Manual
Remote Commands
The Remote Commands Ok item allows you to prevent any commands from being issued from a remote telephone.
If Remote Commands Ok is set to Yes, the OmniLT will allow all commands to be executed when called from a remote
telephone. If Remote Commands Ok is set to No, then lights, appliances, and the security system cannot be controlled from a
remote telephone that dials into your home.
You can issue commands from a local (in-house) phone with Remote Commands Ok set to Yes or No. The default for Remote
Commands Ok is Yes.
Rings Before Answer
Your phone must ring this number of times before the OmniLT will answer an incoming call to your phone.
To change Rings Before Answer, enter the new number from 1 to 15, then press the ' # ' key.
The factory default for Rings Before Answer is 8.
Dial Type
The Dial Type specifies the type of dialing used when the OmniLT dials out. If you do not have Touch-Tone service, then Dial
Type must be set to Pulse.
The default dial type is Tone.
My Phone Number
My Phone Number is the phone number that will be announced when the OmniLT dials out in the event of an alarm. It should be
set to the phone number of the premises where your system is installed.
To enter phone numbers, press the keypad keys 0 - 9. You can put in a dash (-) for legibility by pressing the Off key. Press the ' #
' key after you have pressed all of the digits in the phone number.
For example, to enter the number 555-1234, press 555 'OFF' 1234 #.
Dial Out Number 1
Dial Out Number 1 is one of the 8 numbers that are stored in the system. In the event of an alarm, these numbers are dialed in the
order that is set up in the Dial Out Order for the particular type of alarm.
Dial out numbers 1 - 8 have On and Off times and days, so that no time is wasted calling you at the office at night or on a Sunday
if the alarm is activated.
For dial out number 1, you should enter your office number where you can be reached during working hours.
Enter the phone number the same way as described for My Phone Number.
You can cause the system to pause for two seconds between digits of the number by pressing the DAY key, which puts a T in the
number. Multiple Ts for longer pauses are allowed. You can also press the NIGHT key (*) and the AWAY key (#) for symbols
to get through some types of telephone or pocket beeper/pager systems.
If you wish to remove a phone number for a particular dial out number, press OFF then ' # ' (with the display showing a Dial Out
Number) to enter a single dash (-).
Phone numbers can be up to 24 digits.
DIAL OUT 1 ON
DIAL OUT 1 OFF
The Remote Commands Ok item allows you to prevent any commands from being issued from a remote telephone.
If Remote Commands Ok is set to Yes, the OmniLT will allow all commands to be executed when called from a remote
telephone. If Remote Commands Ok is set to No, then lights, appliances, and the security system cannot be controlled from a
remote telephone that dials into your home.
You can issue commands from a local (in-house) phone with Remote Commands Ok set to Yes or No. The default for Remote
Commands Ok is Yes.
Rings Before Answer
Your phone must ring this number of times before the OmniLT will answer an incoming call to your phone.
To change Rings Before Answer, enter the new number from 1 to 15, then press the ' # ' key.
The factory default for Rings Before Answer is 8.
Dial Type
The Dial Type specifies the type of dialing used when the OmniLT dials out. If you do not have Touch-Tone service, then Dial
Type must be set to Pulse.
The default dial type is Tone.
My Phone Number
My Phone Number is the phone number that will be announced when the OmniLT dials out in the event of an alarm. It should be
set to the phone number of the premises where your system is installed.
To enter phone numbers, press the keypad keys 0 - 9. You can put in a dash (-) for legibility by pressing the Off key. Press the ' #
' key after you have pressed all of the digits in the phone number.
For example, to enter the number 555-1234, press 555 'OFF' 1234 #.
Dial Out Number 1
Dial Out Number 1 is one of the 8 numbers that are stored in the system. In the event of an alarm, these numbers are dialed in the
order that is set up in the Dial Out Order for the particular type of alarm.
Dial out numbers 1 - 8 have On and Off times and days, so that no time is wasted calling you at the office at night or on a Sunday
if the alarm is activated.
For dial out number 1, you should enter your office number where you can be reached during working hours.
Enter the phone number the same way as described for My Phone Number.
You can cause the system to pause for two seconds between digits of the number by pressing the DAY key, which puts a T in the
number. Multiple Ts for longer pauses are allowed. You can also press the NIGHT key (*) and the AWAY key (#) for symbols
to get through some types of telephone or pocket beeper/pager systems.
If you wish to remove a phone number for a particular dial out number, press OFF then ' # ' (with the display showing a Dial Out
Number) to enter a single dash (-).
Phone numbers can be up to 24 digits.
DIAL OUT 1 ON
DIAL OUT 1 OFF
60