Air King 9125H Leaflet

Rev. C 9/07

5084413

2

PRODUCT USAGE
To complete this Air King

®

 High Velocity Head Assembly use any of the following Air King

®

 products:

Model # 9100PB - Pedestal and Base Kit
Model # 9100WC - Wall Mount Kit
Model # 9100CM - Ceiling Mount Kit
Model # 9100WB - Wheel Kit 
Model # 9100I - I-Beam Kit
See Related Product For Assembly Attachment Instructions.

MAINTENANCE

CLEANING: Use a soft cloth and mild soap solution such as liquid dish washing detergent. Dry all parts completely before reconnecting to 

power supply.  

SERVICING: All other servicing, with the exception of general user maintenance, should be performed by an authorized service representative. 

Call 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m.and 5:00 p.m. Eastern for the location of your nearest service 

center.

LUBRICATION: Precision bearings are sealed at the factory for life and do not require further lubrication.

STORAGE: Store the Fan, with these instructions, in a clean and dry place.

CAUTION: TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ONLY 
USE  WITH  ONE  OF  THE  FOLLOWING  AIR  KING  MODELS;  9100PB,  9100WC,  9100CM,  9100WB, 
9100I.  

GRILL AND BLADE ASSEMBLY 

NOTE: The assembly of the blade and grill are identical, regardless if the Fan has an oscillating motor or a non-oscil-

lating motor. One of each is shown in the illustrations below.

1.  Install the 

Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6) 10-32 X 5/16" 

Hex Screws through the 

Rear Grill  into the Motor.  Securely tighten all (6) screws. (Figure 1)

2.  Push the 

Fan Blade onto the Motor Shaft, centering the Hub facing away from the motor, until it stops against the shaft. (Inset A)   Align 

Square Head Bolt with flat of the 

Motor Shaft. TIGHTEN VERY SECURELY WITH AN ADJUSTABLE WRENCH.  Failure to securely tighten 

the Bolt could result in damage to the Fan and/or personal injury. 

3.  Hold the 

Front Grill so that the name, in the center, is right side up and straight across.  Starting at the top: Fasten Front Grill to Rear  Grill 

by sliding the hooked wires on the 

Front Grill over the outermost ring on the Rear Grill. (Figure  2 / Detail A) The bottom most hooks will 

require the use of a flathead screwdriver to complete assembly.  Stand behind the Fan.  Slip the flat of the screwdriver between the Front 
and Rear Grills, next to one of the unfastened hooks. 

(Figure 2 / Detail B) Pull screwdriver handle upwards towards the Rear Grill.  Slip the 

Front Grill hook over the Rear Grill outer ring with a push.  Repeat procedure with remaining hooks.  

OPERATING INSTRUCTIONS

1.

  TO OPERATE: Plug cord into a grounded 120V, 60 Hz outlet. Select desired operating speed with pull cord on the rear of the motor:

 

First pull: High 

Second pull: Medium 

 

Third pull: Low 

Fourth pull: OFF

2. 

TO ADJUST HEAD ANGLE: While holding head firmly, loosen knob under motor (turn counterclockwise). Tilt head to desired position 

FIRMLY retighten knob under motor.

NOTE: The Grill and Blade should be installed AFTER the Motor 

Head Assembly has been properly mounted. 

3. 

OSCILLATION: Push down oscillation knob on motor housing to 

make fan head move from side to side.

 FAN IS SHIPPED WITH 

90º  OSCILLATION  ANGLE.  FOR  45º  OSCILLATION  ANGLE, 

CONNECT THE OSCILLATION LINK TO THE INNERMOST HOLE 

IN THE CAM GEAR. 

1.

2.

3.

Cam Gear

90˚ 

45˚

Rev. C 9/07

5084413

3

IMPORTANT INSTRUCTIONS - OPERATING MANUAL

IMPORTANT INSTRUCTIONS - OPERATING MANUAL