Skylink LK-318-1 Leaflet

1-Button 

Transmitter

LK-318-1

2-Button 

Transmitter

LK-318-2

3-Button 

Transmitter

LK-318-3

Buttons

Red 

LED

Thank  you  for  your  purchase  of  a  SkylinkHome

TM

  Remote,  Model  LK-

318-1/ LK-318-2 / LK-318-3.  This remote which is also called transmitter 

in this document allows you to wirelessly operate SkylinkHome

TM

 receiver 

modules.  

All wireless signal communications within the SkylinkHome

TM

 system are 

based on rolling code technology to ensure highest security is used. 

The following items are included in 

this package:

-   One of LK Series Remotes

-   Lithium Battery CR-2032  (Installed)

-   User’s Instructions

To power the transmitter, simply remove the battery isolator from the 

transmitter, red LED will flash once. Press the button on the transmitter, 

the red LED should flash. The transmitter is now powered properly. If 

the red LED does not flash when button is pressed, refer to Section 6 

“Battery” of this manual.

1) Remove isolator, 

2) LED on for 1 second

In order to operate the receiver module remotely with a transmitter, it 

must be programmed to the receiver module. 

To program a remote to the receiver module, a “Learn” code must be

transmitted, follow the instructions below to transmit the “Learn” code 

to the receiver. 

1. Put the receiver module that you plan to program into programming  

    mode. Refer to the User’s Instructions of that receiver module. 

2. Press 1 and 2 simultaneously and hold for 2 seconds until the LED

    changes from on to flashing quickly. Release the buttons. The red      

    LED on the transmitter will be on for 15 seconds.

3. Press the button on the remote that you plan to use when the LED is 

    steadily on to transmit the “Learn” code. 

4. Once the remote is programmed, the receiver modules will quit from

    programming mode and the programmed transmitter is ready to be

    used now. 

Follow steps 2 and 3 above to transmit the “Learn” code when 

programming the remote to receiver modules. 

You may follow the same instructions to program different buttons on the 

transmitter to different receiver modules.

LED on for 

1 second

Pressing the programmed button on the transmitter once will toggle 

the status of the load that is connected to the receiver module, i.e. if the 

light is off, pressing the button turns on the light, and vice versa. 

When the programmed button is pressed, the red LED flashes briefly 

indicating signal is transmitting. 

The LK-318-3 can be password protected. If you enable the password 

protection,  you  can  only  operate  LK-318-3  after  you  input  the  correct 

password.

Password can be 2-8 digits long, which is a combination of 1, 2 and 3. For 

example, password can be 1, 2, 1, 2. To input this password, you have to 

press button [1], then [2], then [1], then [2].

Note:

[1] = Button 1    [2] = Button 2   [3] = Button 3

Note:

The time-out period is 1 second during above password input.

The  factory  default  password  is  2,  2,  2,  and  this  password  function  is 

disabled out of factory.

1. Press 1 and 3 simultaneously and hold for more than 10 seconds

    until the LED changes from flashing quickly to flashing slowly.

2. Input old password.

3. Press 1 and 3 once simultaneously to confirm. If the password is 

    wrong, the LED will flash 3 times and you have to start it over from

    step1.

4. Input new password.

5. Press 1 and 3 once simultaneously to confirm.

6. Input new password again.

7. Press 1 and 3 once simultaneously to RE-confirm. If the password is

    different from the one of step 4, the LED will flash 3 times and you 

    have to start over from step 1. Otherwise, the password has been

    changed to the new one and the password protection is enabled.

1. Press 1 and 3 simultaneously and hold for more than 5 seconds 

    until the LED flashes quickly but not until the LED flashes slowly. 

2. Input old password.

3. Press 1 and 3 once simultaneously to confirm. If the password is 

    the password protection will be disabled.

1. Press 1 and 3 simultaneously and hold for more than 2 seconds 

    until the LED flashes quickly but not until the LED flashes slowly.

2. Input old password.

3. Press 1 and 3 once simultaneously to confirm. If the password is 

    correct, the password protection will be enabled.

You can toggle the two states - password protection enabled or 

disabled.

Note:

The time-out period is 15 seconds during any of the above setting opera-

tions. After 10 seconds, the LED will flash 3 times and the remote will exit 

from setting.

Remove

isolator

Button [1]

Button [2]

Button [3]