Stovax 8904 Leaflet

PM190-Issue 1 (October 2006)

Ensure that the floor of the fireplace opening is level with 

the projecting hearth surface. If a cement infill is required to 

achieve this, do not proceed with the installation until the 

cement is completely dry.

Cover the surface of the hearth to protect it from damage 

during installation of the cast panel.

Protect the surfaces of the surround (mantelpiece) from damage 

when trial fitting of the panel.

Position the front panel centrally in the fireplace opening 

against the wall. Place the surround (mantelpiece) in position 

and, holding it firmly against the wall, pull the front panel 

forward until it touches the rear of the surround. The panel is 

now in the correct position and should be fixed. The surround 

can be removed while this is completed.

There are a number of ways of fixing the front panel, but a 

typical method is:-

Drill through the 4 corners of the main panel in a position that 

will be covered when the surround is in position. Drill holes in 

the wall in corresponding position, and secure the front panel 

with 75mm (3”) screws and non-plastic wall plugs. Fill any 

gaps between the wall and the panel with a non-combustible 

material, such as fibreglass rope seal or Stovax fire cement, to 

form airtight seal.

Never use strong Portland cement mortar in chimneys and 

fireplaces. A lime based mortar will allow expansion and 

movement and reduce the risk of cracking.

Wait until any cement or seals are dry before fitting a wooden 

surround. If the surround is wood, fix Stovax flat rope seal (Part 

No. 4953) to all surfaces that touch the cast iron panel. Place it 

into position ensuring that it is central, and secure it to the wall 

using flat brass brackets (mirror plates).

With Solid fuel fires use only at a low fire for the first few hours 

of use to allow the castings to temper.

During this time the fireplace may give off some unpleasant 

odours, and we recommend that you keep the room well 

ventilated to avoid a build-up of fumes.

As with all fireplaces the surfaces will become very hot when 

in use, therefore due care should be taken when near the 

fireplace. If it is to be used in the presence of young children, 

elderly or infirm persons a suitable fireguard should be used. 

Care should also be taken with the placement of combustible 

items near the fireplace as conducted and radiated heat could 

cause a fire hazard.

 

Stovax offer a wide range of firescreens and sparkguards, along 

with a hearthgate system designed to offer full protection for a 

range of stoves and fireplaces. Your Stovax dealer can advise 

you on these products.

If a chimney fire occurs evacuate all persons from the building 

before calling the fire brigade. Do not re-enter the building 

until it is confirmed safe to do so.

Following a chimney fire do not use the fireplace until it is 

inspected, by a HETAS (GB only) registered installer, to confirm 

that the appliance is safe to use, or make any repairs required 

before re-use. Only genuine Stovax replacement parts are to be 

used to keep your fireplace in safe and efficient working order. 

After any chimney fire it is recommended that the chimney 

system be inspected and swept by a NACS registered (UK only) 

chimney sweep, to confirm that the system is structurally sound 

and free from any obstructions before re-use.

For fully polished fireplaces Stovax Steel Cleaner (Part No. 

2037) is recommended to keep them clean and rust free. If 

a fire is not to be lit for an extended period, it is advisable 

to coat with a light oil to prevent moisture in the air causing 

surface rust and pitting of the cast iron. This is important when 

plastering or other decorating work is being done.

E & OE.

This product is suitable for use in the stated countries. To install the product in other countries it is essential to obtain translated instructions 

and in some cases the product may require modification. Contact Stovax to obtain further information.