Regency G36D-LP PROPANE User Manual

UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace

1)  Locate appliance
 

a)  Room location, page 6

 

b)  Clearances to Combustibles, pages 6 

-8.

 

c)  Mantle Clearances, page 8

 

d)  Framing & Finishing Requirements, 

  page 

7

 

e)  Venting Requirements, pages 10 - 17.

2)  Assemble Top Standoffs and Top Facing 

Support and Side Nailing Strips, page 9. 
(NOTE: must be done before installing unit 
into fi replace.)

3)  Install vent, pages 20-22.

4)  Make gas and electrical connections. Test 

the pilot. Must be as per diagram. Page 
23.

5)  Install log set where indicated on page 25 

- 27.

6)  Install Flush Door Front (Standard) and 

optional Flush Gold Trim, page 28.

7)  Install Louvers page 28.

8)  Install optional Wall Switch, Remote Control, 

or Wall Thermostat, page 29.

9) Final 

check.

Before leaving this unit with the customer, the 
installer must ensure that the appliance is fi r-
ing correctly and operation fully explained 
to customer.

The G36D-NG or G36D-LP Direct Vent Fireplace 
must be installed in accordance with these in-
structions. Carefully read all the instructions in 
this manual fi rst. Consult the "authority having 
jurisdiction" to determine the need for a permit 
prior to starting the installation. It is the respon-
sibility of the installer to ensure this fi replace 
is installed in compliance with manufacturer's 
instructions and all applicable codes.

Safe installation and operation of this appli-
ance requires common sense, however, we 
are required by the Canadian Safety Standards 
and ANSI Standards to make you aware of the 

1)  The appliance installation must conform 

with local codes or, in the absence of local 
codes, with the current Canadian or National 
Gas Codes, CAN1-B149 or ANSI Z223.1 
Installation Codes.

2)  The appliance when installed, must be 

electrically grounded in accordance with 
local codes, or in the absence of local codes 
with the current National Electrical Code, 
ANSI/NFPA 70 or CSA C22.1 Canadian 
Electrical Code.

3)  See general construction and assembly 

instructions. The appliance and vent should 
be enclosed.

4)  This appliance must be connected to the 

specifi ed vent and termination cap to the 
outside of the building envelope. Never vent 
to another room or inside a building. Make 
sure that the vent is fi tted as per Venting 
instructions.

5)  Inspect the venting system annually for 

blockage and any signs of deterioration.   

6)  Venting terminals shall not be recessed into 

a wall or siding.

7)  Any safety glass removed for servicing 

must be replaced prior to operating the 
appliance.

8)  To prevent injury, do not allow anyone who 

is unfamiliar with the operation to use the 
fi replace.

9)  Wear gloves and safety glasses for protec-

tion while doing required maintenance.

10) Be aware of electrical wiring locations in 

walls and ceilings when cutting holes for 
termination.

11) Under no circumstances should this ap-

pliance be modifi ed. Parts that have to be 
removed for servicing should be replaced 
prior to operating this appliance.

12)  Installation and any repairs to this appliance 

should be done by a qualifi ed service per-
son. A professional service person should 
be called to inspect this appliance annually. 
Make it a practice to have all of your gas 
appliances checked annually.

13) Do not slam shut or strike the glass door.

14) Under no circumstances should any solid 

fuels (wood, paper, cardboard, coal, etc.) 
be used in this appliance.

15) The appliance area must be kept clear and 

free of combustible materials, (gases and 
other fl ammable vapours and liquids).

Emissions from burning  wood or gas could 
contain chemicals known to the State of Cali-
fornia to  cause cancer, birth defects or other 
reproductive harm.