Hearth & Home Technologies CUMBGAP-PMH User Manual
Page 25
Cumberland Gap Wood Stove
R
September 1, 2008
7006-188E
CHIMNEY CLEANING
FORMATION AND NEED FOR REMOVAL:
When wood is burned slowly it produces tar and other organic
vapors which combine with expelled moisture to form creosote. The
creosote vapors condense in the relatively cool chimney flue of a
newly-started or a slow-burning fire. As a result, creosote residue
accumulates on the flue lining. When ignited, this creosote cre-
ates an extremely hot fire which may damage the chimney or even
destroy the house. The chimney connector and chimney should
be inspected at least once every two months during the heating
season to determine if a creosote or soot build-up has occurred.
If creosote has accumulated, it should be removed to reduce the
risk of a chimney fire.
vapors which combine with expelled moisture to form creosote. The
creosote vapors condense in the relatively cool chimney flue of a
newly-started or a slow-burning fire. As a result, creosote residue
accumulates on the flue lining. When ignited, this creosote cre-
ates an extremely hot fire which may damage the chimney or even
destroy the house. The chimney connector and chimney should
be inspected at least once every two months during the heating
season to determine if a creosote or soot build-up has occurred.
If creosote has accumulated, it should be removed to reduce the
risk of a chimney fire.
INSPECTION:
Inspect the system at the stove connection and at the chimney
top. Cooler surfaces tend to build creosote deposits quicker,
so it is important to check the chimney from the top as well as
from the bottom.
top. Cooler surfaces tend to build creosote deposits quicker,
so it is important to check the chimney from the top as well as
from the bottom.
REMOVAL:
I
f soot or creosote have accumulated, it should be removed to
reduce the risk of a chimney fire. Use a brush specifically designed
for the type of chimney in use. A chimney sweep can perform
this service. It is also recommended that before each heating
season the entire system be professionally inspected, cleaned,
and repaired if necessary.
for the type of chimney in use. A chimney sweep can perform
this service. It is also recommended that before each heating
season the entire system be professionally inspected, cleaned,
and repaired if necessary.
Prior to brushing the chimney clean, follow these steps to ensure
that the accumulation of ash and creosote falls directly into the
firebox for removal.
that the accumulation of ash and creosote falls directly into the
firebox for removal.
MAINTENANCE
CREOSOTE
ASH REMOVAL
GLASS CARE
The stove is equipped with ceramic, heat-resistant glass, which can
only be broken by impact or misuse. Do not slam the stove door
or impact the glass. When closing the door, make sure that logs
do not protrude against the glass.
only be broken by impact or misuse. Do not slam the stove door
or impact the glass. When closing the door, make sure that logs
do not protrude against the glass.
Inspect the glass regularly for cracks or breaks. If you detect a
crack or break, extinguish the fire immediately and contact your
dealer for replacement.
crack or break, extinguish the fire immediately and contact your
dealer for replacement.
A portion of the combustion air entering the firebox is deflected
down over the inside of the door glass. This air flow “washes” the
glass, helping to keep smoke from adhering to its surface. When
operated at a low burn rate, less air will be flowing over the glass
and the smokey, relatively cool condition of a low fire will cause the
glass to become coated. Operating the stove with the Primary Air
Slide Control all the way open for 15-20 minutes should remove
the built up coating. If the deposits on the glass are not very heavy,
normal glass cleaners work well. Heavier deposits may be removed
by using a damp cloth dipped in wood ashes or by using a com-
mercially available oven cleaner. After using an oven cleaner, it is
advisable to remove any residue with a glass cleaner or soap and
water. Oven cleaner left on during the next firing can permanently
stain the glass and damage the finish on plated metal surfaces.
down over the inside of the door glass. This air flow “washes” the
glass, helping to keep smoke from adhering to its surface. When
operated at a low burn rate, less air will be flowing over the glass
and the smokey, relatively cool condition of a low fire will cause the
glass to become coated. Operating the stove with the Primary Air
Slide Control all the way open for 15-20 minutes should remove
the built up coating. If the deposits on the glass are not very heavy,
normal glass cleaners work well. Heavier deposits may be removed
by using a damp cloth dipped in wood ashes or by using a com-
mercially available oven cleaner. After using an oven cleaner, it is
advisable to remove any residue with a glass cleaner or soap and
water. Oven cleaner left on during the next firing can permanently
stain the glass and damage the finish on plated metal surfaces.
Do not clean the glass with abrasive materials that may scratch or
otherwise damage the glass. Scratches on the glass can develop
into cracks or breaks. Never attempt to clean the glass while a fire
is in the unit. The best method for maintaining clean glass is to
operate the stove efficiently by using dry, well-seasoned wood and
burning moderate to hot fires.
otherwise damage the glass. Scratches on the glass can develop
into cracks or breaks. Never attempt to clean the glass while a fire
is in the unit. The best method for maintaining clean glass is to
operate the stove efficiently by using dry, well-seasoned wood and
burning moderate to hot fires.
Ash Door
Handle
Handle
Swings Open
REMOVE ALL LABELS FROM GLASS PRIOR TO LIGHTING
THE FIRST FIRE.
THE FIRST FIRE.
This stove is equipped with an ash removal system. We recom-
mend emptying the ash pan at least once a week when the stove
is in constant operation. The amount of ash is dependent on the
type of wood being burned.
mend emptying the ash pan at least once a week when the stove
is in constant operation. The amount of ash is dependent on the
type of wood being burned.
TO
EMPTY
THE
ASH
PAN
AND
DISPOSE
OF
ASHES
:
CAUTION! Ash coals can remain extremely hot for several days.
Protect your hands with gloves when removing the ash pan.
Protect your hands with gloves when removing the ash pan.
DO NOT OPERATE THE STOVE WITH ASH PAN DOOR OPEN
OR WITH ASH PAN REMOVED.
OR WITH ASH PAN REMOVED.
1
.
Allow the stove to cool completely.
2.
Open the hinged ash pan door from the right hand side.
Pull ash pan out carefully.
Pull ash pan out carefully.
3.
Ashes should be placed in a metal container with a tight fit-
ting lid. The closed container of ashes should be placed on
a noncombustible floor or on the ground, well away from all
combustible materials, pending final disposal. If the ashes
are disposed of by burial in soil or otherwise locally dispersed,
they should be retained in the closed container until all cinders
have thoroughly cooled.
ting lid. The closed container of ashes should be placed on
a noncombustible floor or on the ground, well away from all
combustible materials, pending final disposal. If the ashes
are disposed of by burial in soil or otherwise locally dispersed,
they should be retained in the closed container until all cinders
have thoroughly cooled.
4.
Replace ash pan and close ash door.
ASH REMOVAL
1. Remove all ash from the firebox and extinguish all hot embers
before disposal. Allow the stove to cool completely.
2. Disconnect flue pipe or remove baffle from stove before
cleaning chimeny. Otherwise residue can pile up on top of the
baffle and the stove will not work properly;
baffle and the stove will not work properly;
3. Close the door tightly and proceed with sweeping the chim-
ney.
4. Sweep the collected ashes into the ash removal box, and
empty. Clean out the remaining ashes from firebox.
Do not allow ashes to build up in the ashpan until they
reach the grate. This will lead to premature deterioration
of the grate and make it difficult to empty the ash pan.
reach the grate. This will lead to premature deterioration
of the grate and make it difficult to empty the ash pan.