Hearth & Home Technologies PMH User Manual
R
Page 24
7004-187F September 1, 2008
Yosemite Wood Stove
1
. Ensure that the fire is out and the stove is cool to the touch.
2. Protect a table or counter top with padding or towels.
3. Remove door with broken glass by lifting door up and off of the
hinges.
4. Lay door face down on a table or counter making sure door
handle and fiber handle hang over the edge of the table top so
door lays flat, on a soft surface.
door lays flat, on a soft surface.
5. Remove the screws from each glass retainer. If screws are
difficult to remove, soak with penetrating oil first.
6. Remove the glass.
7. Use only 5mm ceramic glass, Part 7004-025.
8. Position the glass with edges evenly overlapping the opening
in the front door.
9. Replace the glass retainers. Be careful not to cross thread the
screws.
10. Tighten each retainer just a few turns until each is secured.
Then continue to tighten each retainer alternately, a few turns
at a time, until the glass panel is tightened snugly.
at a time, until the glass panel is tightened snugly.
11. Replace the door on the stove.
WARNING!
DO NOT OPERATE THE WOODSTOVE IF THE DOOR
GLASS IS BROKEN OR MISSING. DANGEROUS
OVERFIRING CAN OCCUR WHICH CAN DAMAGE THE
APPLIANCE OR IGNITE CREOSOTE IN THE CHIMNEY,
POSSIBLY CAUSING A HOUSE FIRE.
GLASS IS BROKEN OR MISSING. DANGEROUS
OVERFIRING CAN OCCUR WHICH CAN DAMAGE THE
APPLIANCE OR IGNITE CREOSOTE IN THE CHIMNEY,
POSSIBLY CAUSING A HOUSE FIRE.
MAINTENANCE (CONT'D)
GLASS REPLACEMENT
DOOR GASKET
Periodically check the door gasket for proper seal. As the
gasket compresses or “seats” during use, it may become
necessary to replace the gasket material as wear or damage
to the gasket material can cause air leakage into the firebox
resulting in overfiring and loss of efficiency. A replacement
gasket, Part 834-4170, is available from your dealer.
gasket compresses or “seats” during use, it may become
necessary to replace the gasket material as wear or damage
to the gasket material can cause air leakage into the firebox
resulting in overfiring and loss of efficiency. A replacement
gasket, Part 834-4170, is available from your dealer.
Do not clean the glass with abrasive materials that may scratch or
otherwise damage the glass. Scratches on the glass can develop
into cracks or breaks. Never attempt to clean the glass while a fire
is in the stove. The best method for maintaining clean glass is to
operate the stove efficiently by using dry well seasoned wood and
burning moderate to hot fires.
otherwise damage the glass. Scratches on the glass can develop
into cracks or breaks. Never attempt to clean the glass while a fire
is in the stove. The best method for maintaining clean glass is to
operate the stove efficiently by using dry well seasoned wood and
burning moderate to hot fires.
GLASS CARE (CONT'D)
DOOR HANDLE ASSEMBLIES
Fiber Handle
Handle
Lock Nut
Door Cam Latch
Spacing
Washers
Neoprene Washer
Figure 24A -Front Door Handle Assembly
Figure 24B - Side Door Handle Assembly
1. Install washer on door handle shaft.
2. Slide door handle through door.
3. Install additional washer(s) as needed.
4. Install door cam latch and locknut.
2. Slide door handle through door.
3. Install additional washer(s) as needed.
4. Install door cam latch and locknut.
Caution! Do not overtighten locknut. Door handle
needs to move smoothly.
5. Install fiber handle turning clockwise to secure it to
door handle shaft.
CARE AND CLEANING OF
PLATED SURFACES
IMPORTANT: You must clean all the fingerprints and oils from the
plated surfaces before firing the stove for the first time. Use warm
soapy water and a soft rag, glass cleaner and a paper towel, or
vinegar and a paper towel to remove the oils. DO NOT use abra-
sive cleaners! If not cleaned properly prior to lighting the first fire,
the oils can cause permanent stains. The plating will be cured
upon firing of the stove and oils will no longer affect the finish.
Subsequently, little maintenance is then required. Wipe clean as
needed with a soft towel.
plated surfaces before firing the stove for the first time. Use warm
soapy water and a soft rag, glass cleaner and a paper towel, or
vinegar and a paper towel to remove the oils. DO NOT use abra-
sive cleaners! If not cleaned properly prior to lighting the first fire,
the oils can cause permanent stains. The plating will be cured
upon firing of the stove and oils will no longer affect the finish.
Subsequently, little maintenance is then required. Wipe clean as
needed with a soft towel.