Hearth & Home Technologies TIARA II-B User Manual

August 1, 2008

Page  39

Heat & Glo · Tiara I B & Tiara II B · 7010-149M

1.  Set the thermostat to lowest setting. 
2.  Turn off all electric power to the appliance if service is to be performed. 
3.  Push in gas control knob slightly and turn clockwise               to "OFF" position.      

FOR YOUR SAFETY READ BEFORE LIGHTING 

FOR YOUR SAFETY READ BEFORE LIGHTING 

 LIGHTING INSTRUCTIONS 

LIGHTING INSTRUCTIONS 

TO TURN OFF GAS TO APPLIANCE 

TO TURN OFF GAS TO APPLIANCE 

A.  This appliance has a pilot that must be lit manually.  When lighting the pilot, follow these instructions exactly. 
B.  BEFORE LIGHTING, smell around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier 

than air and will settle on the floor. 

 
WHAT TO DO IF YOU SMELL GAS: 
*  Do not try to light any appliance. 
*  Do not touch any electric switch, do not use any phone in your building. 
*  Immediately call your gas supplier from a neighbor's phone.  Follow the gas supplier's instructions. 
*  If you cannot reach your gas supplier, call the fire department. 
C.  Use only your hand to push in or turn the gas control knob.  Never use tools.  If the knob will not push in or turn by hand, don't 

try to repair it, call a qualified service technician.  Force or attempted repair may result in a fire or explosion. 

D. Do not use this appliance if any part has been under water.  Immediately call a qualified service technician to inspect the appliance 

and to replace any part of the control system and any gas control which has been under water. 

1.  STOP!  Read the safety information above on this label. 

2.  Set the thermostat to the lowest setting (if applicable) and turn off 

the switch at the control panel. 

3.  Disconnect the power from the appliance. 
4.  Open the door of the appliance. May need to remove face/front first. 
5.  Push in gas control knob slightly and turn clockwise             to the "OFF"  

position. Do not force. 

6.  Wait five (5) minutes to clear out any gas.  Smell for gas, including near the floor.  If you smell gas, STOP!  Follow "B" of the 

safety information above.  If you don't smell gas go to the next step. 

7.  Push gas control knob in and turn counterclockwise            to the pilot position.  NOTE: Knob cannot be turned unless knob is 

pushed in slightly.  Do not force. 

8. PIEZO IGNITER:  Press down on the gas control knob in pilot position and simultaneously press the piezo igniter.   

(This may take many repetitions for lighting.) 

     ELECTRONIC IGNITER:  If the unit is equipped with an electronic igniter it should begin sparking right away.  
9.  The pilot should be visible through the door opening. 
10.  After the pilot is lit, continue holding control knob down for approximately  

30 seconds.  Release the knob and it will pop back up.  Pilot should remain lit.   

If it goes out, repeat steps 7 through 9. 

*    If the knob does not pop up when released, stop and immediately call your  

service technician or gas supplier. 

*    If the pilot will not stay lit after several tries, turn the gas control knob  

clockwise            to "OFF" and call your service technician or gas supplier. 

11.  Reinstall door and face. Wait five minutes to allow pilot flame to stabilize and 

establish proper draft. 

12.  Push down and turn gas control knob counterclockwise             to "ON". 

13.  Push burner rocker switch on the control panel to "ON".  If thermostat is to be used, leave switch in "OFF" position and set the 

thermostat to desired setting. 

14.  Reconnect electrical power to appliance.