Enviro EG 28 User Manual
TABLE OF CONTENTS
Safety Precautions
2
Code Approvals
3
Deciding where to locate your stove
4
Planning your installation
6
Installation of Log Sets and Embers
14
Operating Instructions
15
Maintenance and Technical
16
Trouble Shooting
17
Gas Line Connection
18
Electrical
19
Parts and Accessories
20
Fuel Conversion
21
Warranty
22
Parts List
23
Exploded Views
24-25
Installation Data Sheet
26
Mobile Home Information
3,13,19,21
CODE APPROVALS
• This Direct Vent appliance draws all of its combustion air from outside of the dwelling through specially
designed vent pipe.
These appliances have been tested by INTERTEK TESTING SERVICES (WH) and found to comply with the
established standards for a DIRECT VENT GAS FIREPLACE in CANADA and the USA as follows:
designed vent pipe.
These appliances have been tested by INTERTEK TESTING SERVICES (WH) and found to comply with the
established standards for a DIRECT VENT GAS FIREPLACE in CANADA and the USA as follows:
LISTED GAS FIRED GRAVITY DIRECT VENT WALL FURNACE (EG 28 DV. Nat. & LPG. )
TESTED TO: ANSI Z21.88-1998 CSA 2.33-M98 VENTED GAS FIREPLACE HEATER. UL307B-1995 GAS
BURNING HEATING APPLIANCES FOR MANUFACTURED HOMES. CGA 2.17-M91 GAS FIRED
APPLIANCES FOR USE AT HIGH ALTITUDE
BURNING HEATING APPLIANCES FOR MANUFACTURED HOMES. CGA 2.17-M91 GAS FIRED
APPLIANCES FOR USE AT HIGH ALTITUDE
SPECS:
ENVIROGAS EG 28 DIRECT VENT UNITS;
• have all been certified for use with either natural or propane gases. (see control panel and rating label.)
• are not for use with solid fuels.
• must not be connected to a chimney flue serving a separate solid-fuel burning appliance.
• are approved for bedroom or bedsitting room.
• have all been certified for use with either natural or propane gases. (see control panel and rating label.)
• are not for use with solid fuels.
• must not be connected to a chimney flue serving a separate solid-fuel burning appliance.
• are approved for bedroom or bedsitting room.
(IN CANADA: must be installed with a listed wall thermostat)
(IN USA: see current ANSI Z223.1 for installation instructions.)
(IN USA: see current ANSI Z223.1 for installation instructions.)
• must be installed in accordance with local codes if any. If none exist use current installation code CAN/CGA
b149 in Canada or ANSI Z223.1 / NFPA 54 in the USA.
• must be properly connected to an approved venting system.
• Manufactured (mobile) home installation must be in accordance with the Manufactured Home Construction
• Manufactured (mobile) home installation must be in accordance with the Manufactured Home Construction
and Safety Standard, UL 307B, Title 24 CFR, Part 3280 and/or The Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A. The unit must be bolted to the floor of the mobile home and must be
electrically grounded to the steel chassis.
Installations, ANSI A225.1/NFPA 501A. The unit must be bolted to the floor of the mobile home and must be
electrically grounded to the steel chassis.
• are approved for installation on combustible materials.
• are not approved for closet or recessed installations.
• are not approved for closet or recessed installations.
ASSEMBLY INSTRUCTIONS
PREPARATION FOR INSTALLATION
• Remove the packaging from the appliance, and check to make sure there is no damage. If damage is found,
• Remove the packaging from the appliance, and check to make sure there is no damage. If damage is found,
please report it to both the carrier and your dealer as soon as possible.
•
Before beginning, carefully check the glass door and the log set
3