Sanyo KS1872 User Manual
85264189988000 © SANYO 2006
In Canada
SANYO FISHER COMPANY
SANYO Canada Inc.
A DIVISION OF SANYO NORTH AMERICA CORPORATION
300 Applewood Crescent, Concord
21605 Plummer Street
Ontario, L4K 5C7, Canada
Chatsworth, CA 91311 U.S.A.
W
Contents
Page
IMPORTANT!
Please Read Before Starting .................................. 2
Please Read Before Starting .................................. 2
1.
GENERAL .......................................................... 3
1-1. Tools Required for Installation (not supplied)
1-2. Accessories Supplied with Unit
1-3. Optional Copper Tubing Kit
1-4. Type of Copper Tube and Insulation Material
1-5. Additional Materials Required for Installation
1-1. Tools Required for Installation (not supplied)
1-2. Accessories Supplied with Unit
1-3. Optional Copper Tubing Kit
1-4. Type of Copper Tube and Insulation Material
1-5. Additional Materials Required for Installation
2.
INSTALLATION SITE SELECTION ................... 4
2-1. Indoor Unit
2-2. Outdoor Unit
2-3. Baffle Plate for the Outdoor Unit
2-1. Indoor Unit
2-2. Outdoor Unit
2-3. Baffle Plate for the Outdoor Unit
3.
HOW TO INSTALL THE INDOOR UNIT ............. 7
3-1. Remove the Rear Panel from the Unit
3-2. Make a Hole
3-3. Install the Rear Panel on the Wall
3-4. Remove the Grille to Install the Indoor Unit
3-5. Shape the Indoor Side Tubing
3-6. Wiring Instructions
3-7. Recommended Wire Length and Diameter
3-8. Wiring Instructions for Inter-unit Connections
3-9. Mounting
3-10. Drain Hose
3-1. Remove the Rear Panel from the Unit
3-2. Make a Hole
3-3. Install the Rear Panel on the Wall
3-4. Remove the Grille to Install the Indoor Unit
3-5. Shape the Indoor Side Tubing
3-6. Wiring Instructions
3-7. Recommended Wire Length and Diameter
3-8. Wiring Instructions for Inter-unit Connections
3-9. Mounting
3-10. Drain Hose
4.
HOW TO INSTALL THE OUTDOOR UNIT ....... 17
4-1. Wiring Instructions for the Outdoor Unit
4-1. Wiring Instructions for the Outdoor Unit
5.
REFRIGERANT TUBING .................................. 18
5-1. Use of the Flaring Method
5-2. Flaring Procedure with a Flare Tool
5-3. Caution before Connecting Tubes Tightly
5-4. Connecting Tubing between Indoor and
5-1. Use of the Flaring Method
5-2. Flaring Procedure with a Flare Tool
5-3. Caution before Connecting Tubes Tightly
5-4. Connecting Tubing between Indoor and
Outdoor Units
5-5. Insulation of Refrigerant Tubing
5-6. Taping the Tubes
5-7. Finishing the Installation
5-6. Taping the Tubes
5-7. Finishing the Installation
6.
AIR PURGING................................................... 20
I
Air Purging with a Vacuum Pump (for Test Run)
I
Basic Functions of the Service Valves
I
Pump Down
INSTALLATION INSTRUCTIONS
Model Combinations
Combine indoor and outdoor units only as listed
below.
below.
Indoor Unit
Outdoor Unit
KS1872
C1872
CL1872
KS2472
C2472
CL2472
Power Source:
60 Hz, single-phase, 230/208 V
60 Hz, single-phase, 230/208 V
– Inverter Split System Air Conditioner –
COOL / DRY Model
This air conditioner uses the new refrigerant R410A.
Be sure to read the yellow instruction sheet
attached to the outdoor unit for models using the
new refrigerant R410A.
The illustrations are based on the typical appearance of
a standard model. Consequently, the shape may differ
from that of the air conditioner that you are installing.
NOTE
7.
REMOTE CONTROL UNIT INSTALLATION
POSITION ......................................................... 24
7-1. Mounting on a Wall
POSITION ......................................................... 24
7-1. Mounting on a Wall
8.
ADDRESS SWITCH .......................................... 25
8-1. Address Setting of the Remote
8-1. Address Setting of the Remote
Control Unit
05-326 AirCon_85264189988000 12/5/05 3:35 PM Page a