Runco LS-100d User Manual
Lightstyle™ Series LS-100d Installation/Operation Manual
9
PRE
L
IMINAR
Y
1.
MAIN POWER SWITCH
Disconnects or applies power to the DHD Controller.
Disconnects or applies power to the DHD Controller.
2.
TRIGGERS
Connection for up to three (3), 12-volt trigger-controlled devices such as retractable
screens or screen masks. Output current is limited to 250 milliamperes (mA).
Connection for up to three (3), 12-volt trigger-controlled devices such as retractable
screens or screen masks. Output current is limited to 250 milliamperes (mA).
3.
USB
A standard, USB Series “B” connection to a personal computer, for performing
software upgrades and other service procedures.
A standard, USB Series “B” connection to a personal computer, for performing
software upgrades and other service procedures.
4.
RS-232 (To Accessory Box)
A male, 9-pin D-sub connector for interfacing with external equipment. (For future
use.)
A male, 9-pin D-sub connector for interfacing with external equipment. (For future
use.)
5.
Display Control
Connect this to the RS-232 input on the LS-100d projector, using the supplied
communication cable and null-modem adapter (refer to Connecting the DHD
Controller to the LS-100d on page 19).
Connect this to the RS-232 input on the LS-100d projector, using the supplied
communication cable and null-modem adapter (refer to Connecting the DHD
Controller to the LS-100d on page 19).
6.
IR
Wired input from a Niles- or Xantech-compatible, infrared (IR) repeater system. It is a
3.5-mm, mini phono jack, wired as follows:
Ring = No connection
Tip = IR Input
Sleeve = Ground
Wired input from a Niles- or Xantech-compatible, infrared (IR) repeater system. It is a
3.5-mm, mini phono jack, wired as follows:
Ring = No connection
Tip = IR Input
Sleeve = Ground
7.
POWER INPUT (100 to 240 VAC)
Connect the DHD Controller to power here.
Connect the DHD Controller to power here.
8.
HD1 / HD2 (5 x Analog BNCs)
Two inputs (five BNCs per input) for connecting standard-definition (SD = 480i/576i),
enhanced-definition (ED = 480p/576p) or high-definition (HD = 720p/1080i/1080p)
component video sources, or RGBHV sources such as personal computers.
Two inputs (five BNCs per input) for connecting standard-definition (SD = 480i/576i),
enhanced-definition (ED = 480p/576p) or high-definition (HD = 720p/1080i/1080p)
component video sources, or RGBHV sources such as personal computers.
9.
Component / SCART (3 x RCA connectors)
SD/HD input for connecting SDTV, EDTV or HDTV component video sources. Also
provides RGB input for SCART RGBS sources.
SD/HD input for connecting SDTV, EDTV or HDTV component video sources. Also
provides RGB input for SCART RGBS sources.
10. Video 1 / Video 2 / Video 3
Standard, composite video inputs for connecting a VCR, camcorder or other
composite video source. The Video 1 input also provides composite sync input for
SCART RGBS sources.
composite video source. The Video 1 input also provides composite sync input for
SCART RGBS sources.
11. HDMI 1 / HDMI 2 / HDMI 3 / HDMI 4 (Digital)
HDCP-compliant digital video inputs for connecting an HDMI or DVI source.
12. Ethernet
A female RJ-45 connector for wired network communications.
13. HDMI Out (Audio Only)
Connect this output to an audio control system to pass through HDMI audio.
14. HDMI Out (To Display)
Connect this to the DHD Input on the LS-100d (see Figure 2-2).
15. RS-232 (PC / Control)
A female, 9-pin D-sub connector for interfacing with a PC or automation/control
system.
system.