Hearth & Home Technologies CASTINS-CSB User Manual

Page of 48
Page  2
250-7251F
September 1, 2008
R
Castile Pellet Insert
Hearth & Home Technologies welcomes you to our 
tradition of excellence!  In choosing a Quadra-Fire 
appliance, you have our assurance of commitment 
to quality, durability, and performance.
This commitment begins with our research of the 
market, including ‘Voice of the Customer’ contacts, 
ensuring we make products that will satisfy your 
needs. 
Our Research and Development facility then 
employs the world’s most advanced technology 
to achieve the optimum operation of our stoves, 
inserts and fireplaces.  And yet we are old-fash-
ioned when it comes to craftsmanship.  Each unit 
is meticulously fabricated and are hand-finished for 
lasting beauty and enjoyment.  
Our pledge to quality is completed as each model 
undergoes a quality control inspection.  From 
design, to fabrication, to shipping:  We wish you 
and your family many years of enjoyment in the 
warmth and comfort of your hearth appliance.  
Thank you for choosing Quadra-Fire.
SAMPLE OF CLEARANCE TO COMBUSTIBLES LABEL
LOCATION:  On beaded chain behind right access 
panel.  Panel hinges open.
Report No. 
#061-S-42-2
7014-143
SAFETY LABEL
R
Castile Pellet Insert
Listed Solid Fuel Room Heater/Pellet Type Insert.  Also suitable for Mobile Home Installation.  This 
appliance has been tested and listed for use in Manufactured Homes in accordance with OAR 
814-23-9000 through 814-23-909.
Tested to: ASTM E-1509-95, ULC S628-93, ULC /ORD-C1482-M1990 Room Heating Pellet Burning Type, 
(UM) 84-HUD FOR USE ONLY WITH PELLETIZED WOOD OR SHELLED FIELD CORN FUEL.
Route power cord away from unit. Do not route cord under or in front of appliance.
Input Rating:  30,000 BTU/HR. 
Electrical Rating: 115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 AMPS.
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
AS A BUILT-IN UNIT
Masonry or Zero Clearance
DO NOT REMOVE THIS LABEL
A  Insert side to combustible 
0 in. 
0mm
Insert top to mantel 
 12 
in. 305mm
C  Insert top to face trim 
             0 in. 
0mm
Insert side face trim  
 
in. 
0mm
E  Hearth extension from door opening   
6 in. 
152mm
Hearth extension from side of door opening 6 
in.  152mm
B
D
C
C
A
B
E
0 in. Clearance To Exposed Section and Face Trim
A  Top of Hopper   
       Top/Rear Vent   0 in.     (0mm)
Side of Outside Skin         Top/Rear Vent   0 in.     (0mm)
C  Back of Hopper 
       Rear Vent          0 in.    (0mm)
 
 
Top Vent 
     2.5 in. (64mm)
Vent Pipe to Combustible Rear Vent          3.0 in.  (76mm)
E  From Panel Edge 
 
     0 in.     (0mm)
SIDE W
ALL
MANTEL
B
A
C
E
D
F
Face Trim
1445 Highway North, Colville, WA  99114
Manufactured by:
www.quadrafire.com
O-T L
Tested and 
Listed by
Portland
Oregon USA
OMNI-Test Laboratories, Inc.
C
US
SAMPLE
This model is exempt from EPA certification 
under 40 CFR 60.531 by definition [Wood 
Heater (A) "Air-to-Fuel Ratio"].
AN FEB MAR 
APR MAY UNE ULY AU  SEPT 
OCT NOV DEC
0-7
F
CASTILE PELLET INSERT
R
SERIAL NO. / NUM RO DU S RIE
DO NOT REMOVE THIS LABEL 
Made in U.S.A.
Report / Rapport
#061-S-42-2
C T
TTE T
T  E    ER T     T T C   EE  C RE  C T    F R T RE 
. C T CT   C SE S  
R S.  SEE  E TE    STR CT S. perate t is  nit  it   el  opper lid closed.  Fail re to do so ma  
res lt in emissions prod cts com stion  rom t e  opper  nder certain conditions.   aintain  opper seal in 
ood condition.  o not o er ill  opper.
C
  RS E  R T . E  S T C ER.  R E  ES E F TS ET ES  TE E TS   E 
ES CE  S
 E  ST
T . E C T CT E T C SER ES R RES    E .   R 
T ETTE ET  ES  STR CT S.  p re  cet appareil a ec le co ercle de la tr mie erm .  e d a t de ne pas s i re les instr ctions 
pe t r s lter so s certaines conditions en  ne com stion des  missions des prod its  enant de la tr mie.  e pas remplir la tr mie trop pleine.
007
00    00     010 
U.S. ENVIRONMENTAL 
PROTECTION A ENCY
 NE PAS ENLEVER L TI UETTE
Fait A
  tats-Unis
O-T L
Tested and 
Listed by
Portland
Oregon USA
OMNI-Test Laboratories, Inc.
C
US
Test Lab & 
Rpt Nbr.
Mfg Date
Model
Name
Serial No.
SAMPLE OF SERIAL NUMBER & DATE OF MANUFACTURE LABEL
LOCATION:   Inside hopper on the top