DLS Svenska AB DLS CA12 User Manual
Tools and material needed
Tools:
Flat and Phillips screwdrivers
Wire cutter
Wire stripper
Electric drill with drills
Crimping tool
Digital multimeter or test lamp
Wire brush, scraper or a piece
of an abrasive sheet to remove
paint for a good ground connection
Grease to protect the ground
connection from corrosion
Wire cutter
Wire stripper
Electric drill with drills
Crimping tool
Digital multimeter or test lamp
Wire brush, scraper or a piece
of an abrasive sheet to remove
paint for a good ground connection
Grease to protect the ground
connection from corrosion
Material:
Speaker wire: minimum
12 AWG = 4 mm
12 AWG = 4 mm
2
for subwoofers
Sheet metal screws for mounting the
amplifier to the amplifier board and the
amplifier board to the car + some extra
for fuse holder, amplifier ground etc.
amplifier to the amplifier board and the
amplifier board to the car + some extra
for fuse holder, amplifier ground etc.
Electrical insulation tape
½ inch thick plywood or particle board for
the amplifier to be mounted upon.
the amplifier to be mounted upon.
Amplifier installation kit:
If available,buy an amplifier installation kit. It
contains normally all you need. This is what you
have to buy if you buy the items separately
If available,buy an amplifier installation kit. It
contains normally all you need. This is what you
have to buy if you buy the items separately
20- 25 feet = 6- 7.5 meter power cable,
minimum AWG 5 = 16 mm
minimum AWG 5 = 16 mm
2
or heavier.
1 pc of fuseholder to install close to the
car battery + fuse 60 Ampere.
20 feet of AWG 15 = 1,5 mm
car battery + fuse 60 Ampere.
20 feet of AWG 15 = 1,5 mm
2
wire for
remote turn on / off cable from radio.
RCA-cable for input from radio.
- 20 feet or 5 meter for trunk installations
-12 feet or 2 – 3 meter for under seat
installations
Two ring crimp terminals –one
for connection to the battery plus and one
for the amplifier ground connection.
Two heavy fork crimp terminals to connect
+ and – to amplifer – but you do only need
them if you use heavy cable or to make the
installation look nicer.
Four to eight fork crimp terminals to
connect the speaker cables – but you do
only need them if you use heavy cables or
want the installation to look nicer.
One fork crimp terminal to connect the
remote wire to the amplifier, but you need it
only to make it look nicer.
Four to eight splicers to connect speaker
cables to high level input cable, if high level
input is used.
Wire ties
Insulating grommet or insulating tube
RCA-cable for input from radio.
- 20 feet or 5 meter for trunk installations
-12 feet or 2 – 3 meter for under seat
installations
Two ring crimp terminals –one
for connection to the battery plus and one
for the amplifier ground connection.
Two heavy fork crimp terminals to connect
+ and – to amplifer – but you do only need
them if you use heavy cable or to make the
installation look nicer.
Four to eight fork crimp terminals to
connect the speaker cables – but you do
only need them if you use heavy cables or
want the installation to look nicer.
One fork crimp terminal to connect the
remote wire to the amplifier, but you need it
only to make it look nicer.
Four to eight splicers to connect speaker
cables to high level input cable, if high level
input is used.
Wire ties
Insulating grommet or insulating tube
Routing wires
Stereo
head unit
3
Professional Tip:
If amplifier installation kits are available with diffe-
rent size of power cable, chose the most heavy
power cable to improve sound quality and to allow
more amplifiers to be installed now or later.
rent size of power cable, chose the most heavy
power cable to improve sound quality and to allow
more amplifiers to be installed now or later.
If possible buy AWG 4 = PL 21 mm
2
(or heavier)
cable for best performance.
High current draw
The CA12 is a mono amplifier with high power output.
The current draw is also high so you must make sure
that your vehicles power system (battery and alternator)
can provide all the power you need. If you have a bad
battery or alternator in can result in a poor sound or
even worse, a broken battery or alternator.
The current draw is also high so you must make sure
that your vehicles power system (battery and alternator)
can provide all the power you need. If you have a bad
battery or alternator in can result in a poor sound or
even worse, a broken battery or alternator.
CA12