Jensen VM9311 User Manual
5
VM9311
INSTALLATION
Pre-installation
1.
Press the metal levers on both sides to remove the half-
sleeve from the radio.
sleeve from the radio.
2.
Install the half-sleeve.
a. Install adaptor if necessary (optional).
b. Install half-sleeve into adaptor or dashboard (only use
b. Install half-sleeve into adaptor or dashboard (only use
the supplied screws). Do not force the sleeve into the
opening or cause it to bend or bow.
opening or cause it to bend or bow.
c. Locate the series of bend tabs along the top, bottom
and sides of the mounting sleeve. With the sleeve fully
inserted into the dashboard opening, bend as many of
the tabs outward as necessary so that the sleeve is
firmly secured to the dashboard.
inserted into the dashboard opening, bend as many of
the tabs outward as necessary so that the sleeve is
firmly secured to the dashboard.
d. Install support strap to make the unit more stable.
CAUTION! Be careful not to damage the car wiring.
4.
Place the radio in front of the dashboard opening so the
wiring can be brought through the mounting sleeve.
wiring can be brought through the mounting sleeve.
Wiring
Complete wiring as illustrated in the wiring diagrams on
pages 3 and 4. Once the wiring is complete, reconnect the
battery negative terminal. If there is no ACC available,
connect the ACC lead to the power supply with a switch.
pages 3 and 4. Once the wiring is complete, reconnect the
battery negative terminal. If there is no ACC available,
connect the ACC lead to the power supply with a switch.
NOTE: When replacing a fuse, be sure to use correct
type and amperage to avoid damaging the radio. The
VM9311 uses one 15 amp mini-ATM fuse, located in the
black filter box in-line with the main wire harness.
type and amperage to avoid damaging the radio. The
VM9311 uses one 15 amp mini-ATM fuse, located in the
black filter box in-line with the main wire harness.
Final Installation
After completing the wiring connections, turn the unit on to
confirm operation (ignition switch must be on). If unit does not
operate, recheck all wiring until problem is corrected. Once
proper operation is achieved, turn off the ignition switch and
proceed with final mounting of the chassis.
confirm operation (ignition switch must be on). If unit does not
operate, recheck all wiring until problem is corrected. Once
proper operation is achieved, turn off the ignition switch and
proceed with final mounting of the chassis.
1.
Connect wiring adaptor to existing wiring harness.
2.
Connect antenna lead.
3.
Carefully slide the radio into the half-sleeve making sure
it is right-side-up until it is fully seated and the spring
clips lock it into place.
it is right-side-up until it is fully seated and the spring
clips lock it into place.
NOTE: For proper operation of the CD/DVD player, the
chassis must be mounted within 20° of horizontal. Make
sure the unit is mounted within this limitation.
chassis must be mounted within 20° of horizontal. Make
sure the unit is mounted within this limitation.
4.
Attach one end of the perforated support strap
(supplied) to the screw stud on the rear of the chassis
using the hex nut provided. Fasten the other end of the
perforated strap to a secure part of the dashboard either
above or below the radio using the screw and hex nut
provided. Bend the strap to position it as necessary.
(supplied) to the screw stud on the rear of the chassis
using the hex nut provided. Fasten the other end of the
perforated strap to a secure part of the dashboard either
above or below the radio using the screw and hex nut
provided. Bend the strap to position it as necessary.
CAUTION! The rear of the radio must be supported with
the perforated strap to prevent damage to the dashboard
from the weight of the radio or improper operation due to
vibration.
the perforated strap to prevent damage to the dashboard
from the weight of the radio or improper operation due to
vibration.
5.
Replace any items you removed from the dashboard.
Final ISO-DIN Installation
1.
Remove trim ring.
2.
Mount factory brackets on new radio using existing
screws from old radio.
screws from old radio.
3.
Slide radio chassis into dash opening and secure.
4.
Reinstall dash panel.
PREPARE RADIO
INSTALL HALF SLEEVE
2
1
3
4
7-INCH
TFT
7-INCH
TFT
MODE
VM9510
MUTE
AS/PS
BAND
DISP
PWR
ENTER
AM/FM/DVD/MP3
RECEIVER
7-INCH
DIGITAL
TFT
OPEN
Push
Push
AV AUX
IN
5
FINAL INSTALLATION
3
4
7-INCH
TFT
7-INCH
TFT
MODE
VM9510
MUTE
AS/PS
BAND
DISP
PWR
ENTER
AM/FM/DVD/MP3
RECEIVER
7-INCH
DIGIT
AL TFT
OPEN
Push
Push
AV AUX
IN
2
1
FINAL ISO-DIN INSTALLATION