Blaupunkt CD33 User Manual
ENGLISH
E-3
General Operations
Turning the power On/Off
Press the
PWR
to turn the unit On or Off.
Tip
When you turn on the unit, “HELLO” will be displayed then
“WELCOME” will momentarily be displayed before actual
power on.
When you turn off the unit, “SEE YOU” will be displayed then
“GOOD-BYE” will momentarily be displayed before actual
power off.
You can edit these messages. (See “Turn on/off message edit”).
When you turn on the unit, “HELLO” will be displayed then
“WELCOME” will momentarily be displayed before actual
power on.
When you turn off the unit, “SEE YOU” will be displayed then
“GOOD-BYE” will momentarily be displayed before actual
power off.
You can edit these messages. (See “Turn on/off message edit”).
Volume Control
Rotate the VOL dial to adjust the volume.
Volume up
Volume down
+
+
-
-
VOL
VOL
Muting the sound
Press
MUTE / SENS
.
To restore the previous volume level, press
MUTE / SENS
again.
Mute level can be adjustable. (See “
Adjusting the Sound
Characteristics”)
Switching the Source (Selecting auxiliary
input)
input)
You can connect auxiliary equipment (Portable cassette player,
etc) to this radio via optional AUX-IN cable. (See page 13)
etc) to this radio via optional AUX-IN cable. (See page 13)
Each time the
CD
is pressed, the operation source will
change over as shown below;
CD
CD changer or AUX
RADIO
Press the
BAND
to return to tuner mode.
Notes
• If the
• If the
CD
button is pressed when no CD has been loaded
into the unit, The CD mode will skip to the CD changer
mode or AUX mode.
Also, if the CD changer is not connected, the system will
move across to the AUX mode regardless of whether auxil-
iary equipment is connected or not (“ AUX ” will be dis-
played.)
mode or AUX mode.
Also, if the CD changer is not connected, the system will
move across to the AUX mode regardless of whether auxil-
iary equipment is connected or not (“ AUX ” will be dis-
played.)
• It is not possible to switch to the AUX mode when the CD
changer is connected.
Setting the Clock
The clock uses a 12-hour display system.
1.
Turn the ignition key to the ON position.
2.
Press the
PWR
to turn on the unit.
3.
Repeatedly press the
DISP
to display “CLK ADJ.
4.
Use the following buttons and dial to set the clock. (The blink-
ing section can be adjusted.)
ing section can be adjusted.)
SC/PS
: To switch Hour/Minute blink
+
+
-
-
VOL
VOL
: Adjust the Hour and minute
5.
Press the
DISP
momentarily to complete the Clock set-
ting mode.
Ignition-off Clock Recall
The display will illuminate showing the time and then auto-
matically shut off after 5 seconds.
matically shut off after 5 seconds.
Press the
DISP
while the ignition switch is in the “ OFF ” po-
sition.
Adjusting the Sound Characteristics
1.
Each time you press the
AUDIO
to select the desired ad-
justment mode as table below.
After pressing the
After pressing the
AUDIO
, you can also select with TUN/
TRK dial or
DISP
.
2.
Rotate the VOL dial to adjust the selected item.
Use the following tables as a guide for adjusting the set-
tings in each mode.
Adjust within 5 seconds after selecting the item. After 5
seconds, the unit returns to previous indication.
Use the following tables as a guide for adjusting the set-
tings in each mode.
Adjust within 5 seconds after selecting the item. After 5
seconds, the unit returns to previous indication.
+
+
-
-
VOL
VOL
Adjustment Range
bAS
B 0 (BASS)
B –5
~
B 0
~
B +5
TRE
T 0 (TREBLE)
T –5
~
T 0
~
T +5
Ld
LOUD
LOUD
OFF
–
LOUD ON
bAS
X-BASS
X-BASS
0
~
X-BASS 4
bAL
B 0 (BALANCE) B L9
~
B 0
~
B R9
FAd
F 0 (FADER)
F R9
~
F 0
~
F F9
AU
GAIN
–6
~
0
~
3
LMt
LEVEL
0
~
50
~
80
MUt
LEVEL
0
~
20
~
80
•A italicized letter is an initial value.
SacramentoCD33_Eng
2/5/03, 4:27 PM
3