Blaupunkt 7 649 020 110 User Manual
22
Placing the device in operation
Placing the device in operation
Detaching/attaching the control
panel
panel
The device is equipped with a detachable control
panel (fl ip-release panel) as a way of protecting
your equipment against theft. Always take the
control panel with you when leaving the vehicle.
The device is worthless to a thief without this con-
trol panel.
panel (fl ip-release panel) as a way of protecting
your equipment against theft. Always take the
control panel with you when leaving the vehicle.
The device is worthless to a thief without this con-
trol panel.
Caution
Damage to the control panel
Never drop the control panel.
Do not expose the control panel to direct sunlight
or another heat source.
or another heat source.
Avoid direct skin contact with the control panel’s
electrical contacts.
electrical contacts.
Removing the control panel
Press the
button
1 to unlock the control
panel.
Grasp the control panel at the left side and
fi rst pull it straight out of the bracket and
then to the left.
fi rst pull it straight out of the bracket and
then to the left.
Attaching the control panel
Push the control panel into the bracket at the
right edge of the device.
right edge of the device.
Push the control panel carefully into the left
bracket until it clicks into place.
bracket until it clicks into place.
Switching on/off
With the vehicle ignition switched on, briefl y
press the On/Off button
press the On/Off button
4 to switch on the
device.
- or -
Press the On/Off button
4
for approx.
2 seconds to switch off the device.
The device remembers the audio source played
last for the next switch-on. Any CD already insert-
ed in the device remains there.
last for the next switch-on. Any CD already insert-
ed in the device remains there.
쏅
쏅
쏅
쏅
쏅
쏅
Notes:
If the vehicle ignition is switched off, the
device cannot be switched on with the On/
Off button
device cannot be switched on with the On/
Off button
4.
The device is switched off and on again
with the vehicle ignition if it is connected
with the ignition (see the installation in-
structions).
with the vehicle ignition if it is connected
with the ignition (see the installation in-
structions).
Adjusting the volume
You can adjust the volume in increments from
0 (off) to 66 (maximum).
0 (off) to 66 (maximum).
Turn the On/Off button
4 to change the
volume.
Note:
If a telephone or navigation system is con-
nected with the device as described in the
installation instructions, the device is muted
with every telephone call or a navigation
announcement. The display then shows
"PHONE".
If a telephone or navigation system is con-
nected with the device as described in the
installation instructions, the device is muted
with every telephone call or a navigation
announcement. The display then shows
"PHONE".
"NO SRC" mode (muted)
Instead of an audio source, you can select the
"NO SRC" mode ("No Source": no audio source).
"NO SRC" mode ("No Source": no audio source).
In the "NO SRC" mode, no audio source is select-
ed. The device is muted and may automatically
switch off after a predefi ned time, if set (see the
chapter "User settings", section "Performing set-
tings in the user menu", menu item "OFF").
ed. The device is muted and may automatically
switch off after a predefi ned time, if set (see the
chapter "User settings", section "Performing set-
tings in the user menu", menu item "OFF").
Certain user settings can be performed only in the
"NO SRC" mode.
"NO SRC" mode.
Changing to "NO SRC" mode
Press the On/Off button
4
repeatedly until
"NO SRC" appears.
•
•
쏅
쏅
02_BuenAir200_Stock100_gb.indd 22
02_BuenAir200_Stock100_gb.indd 22
03.12.2008 13:18:00 Uhr
03.12.2008 13:18:00 Uhr