Fusion MS-DA51600 User Manual
2
AMPLIFIER SPECIFICATIONS
Peak Power (Watts)
1600
Frequency Response
10Hz -50kHz
Dimensions (mm)
300(l) x 210(w) x 50(h)
11-13/16 x 8-1/4 x 2”
11-13/16 x 8-1/4 x 2”
Power Ratings
80W RMS x 4 +
250W RMS x 1 @ 4Ω 1% THD+N
130W RMS x 4 +
330W RMS x 1 @ 2Ω 1% THD+N
250W RMS x 2 @ 4Ω Bridged 1% THD+N +
250W RMS x 1 @ 4Ω 1% THD+N
130W RMS x 4 +
330W RMS x 1 @ 2Ω 1% THD+N
250W RMS x 2 @ 4Ω Bridged 1% THD+N +
250W RMS x 1 @ 4Ω 1% THD+N
INSTALLATION GUIDELINES
1. Ensure the +12V lead is disconnected from the
battery before you connect any new equipment.
2. Ensure the mounting location will not interfere
with the gas tank or electrical wiring.
3. Ensure the Amplifier is securely fastened to the
vessel to prevent injury in the event of an accident.
4. Ensure all wiring is protected to avoid pinching
or crushing which could result in damage to the
audio system.
audio system.
5. Ensure the mounting location has sufficient
air flow around the amplifier. If the amplifier is
mounted in an enclosed space a 3” fan with
ducting should be used to aid in air flow.
mounted in an enclosed space a 3” fan with
ducting should be used to aid in air flow.
6. Do not mount any amplifier on a subwoofer
enclosure as extended exposure to vibration may
cause malfunction of the amplifier.
cause malfunction of the amplifier.
7. Ensure you use the recommended gauge wire/
cable for all amplifier connections.
WIRING
Ensure the audio system is turned off before making any
connections to the amplifier, speakers or source unit,
failure to do so could result in permanent damage to the
audio system.
When wiring the FUSION amplifier ensure that the cable
is protected from sharp objects and always use rubber
grommets when wiring through metal panels.
Ensure all terminals and connections are protected from
the vessel chassis and from each other as failure to do so
could result in permanent damage to the audio system.
connections to the amplifier, speakers or source unit,
failure to do so could result in permanent damage to the
audio system.
When wiring the FUSION amplifier ensure that the cable
is protected from sharp objects and always use rubber
grommets when wiring through metal panels.
Ensure all terminals and connections are protected from
the vessel chassis and from each other as failure to do so
could result in permanent damage to the audio system.
+12V CONNECTION
FUSION amplifiers should be connected directly to the
+12V battery terminal with an inline fuse or circuit
breaker as close the battery as possible.
+12V battery terminal with an inline fuse or circuit
breaker as close the battery as possible.
GROUND CONNECTION
When grounding/earthing your amplifier ensure that the
location is a good source of ground. Make sure the metal
is clean of paint etc as a poor earth could damage your
audio system.
location is a good source of ground. Make sure the metal
is clean of paint etc as a poor earth could damage your
audio system.
REMOTE TURN-ON CONNECTION
This connection turns the amplifier on & should be
connected to the remote turn on wire from the Head
Unit. If one is not available a switched 12v source must
be used.
connected to the remote turn on wire from the Head
Unit. If one is not available a switched 12v source must
be used.
RCA INPUTS
Choose the correct length RCA cable & run them to the
RCA outputs of the source/head unit, avoiding running
beside other looms & or power cable.
RCA outputs of the source/head unit, avoiding running
beside other looms & or power cable.