Jensen SOOGM-16 Leaflet

CRUX GMLAN ONSTAR

BACK UP CAMERA

USING THE MUTE CIRCUIT BOARD (FIG 1)

The external mute circuit is used to mute the audio on your radio.

Determine whether your radio is equipped with BOSE, then place

the 8 pin connector into the proper female connector. Reference the

sticker on the mute circuit board.

RADIO REMOTE SELECT:

0. Pioneer

1. Alpine

2. Clarion

3. Kenwood

4. JVC

5. Sony/Jensen/Dual

TO FACTORY

HARNESS

24-PIN

(male plug)

AFTERMARKET

RADIO

MATCH LOOSEWIRES TO AFTERMARKET RADIO

front left speakers

front right speakers

rear left speakers

rear right speakers

constant

accessory

ground

illumination

amp on

vss

swc

8-PIN

(male plug)

12-PIN

(male plug)

INTERFACE

THIS HARNESS ONLY HAS

3-PINS POPULATED.

DO NOT PLUG IN THE

FULLY POPULATED 8-PIN.

16-PIN

(male plug)

14-PIN

(male plug)

8-PIN

(male plug)

MUTE

CIRCUIT

BOARD

(SEE FIG 1)

Black

= Ground

Red

= Accessory

Yellow

= Constant

Orange

= Illumination

Blue/White

= Amplifier Turn-On

White

= Left Front (+)

White/Black

= Left Front (-)

Gray

= Right Front (+)

Gray/Black

= Right Front (-)

Green

= Left Rear (+)

Green/Black

= Left Rear (-)

Purple

= Right Rear (+)

Purple/Black

= Right Rear (-)

Purple/White

= Vehicle Speed Sense

Blue/Yellow

= SWC (Kenwood/ JVC)

Orange/White

= Dimmer

Yellow/Black

= Parking Brake

Red/White

= Reverse Gear

We recommend reading this installation guide first before starting any

work. Following these instructions from “Start” to” Finish” will ensure

a smooth and hassle free installation. We offer telephone support M-F

9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.

PARTS INCLUDED:

(1) Interface Module

(1) GM 29-Bit Harness (Part Number: Crux2513)

(1) Instruction Sheet

(1) Reverse Camera Harness (CJA2103A)

PRECAUTIONS:

- Remove the negative side of the battery to avoid any short circuits

durring the installation.

- Do not install the interface near any major components or near the

HVAC system. This may cause damage or overheating to the vehicle.

PRELIMINARY:

Please read the entire mannual before installing this interface.

This unit provides the following:

- 12V Acc Output (3A Max/ RAP)

- Illumination Output (250mA Max)

- Low Voltage (Batt Run-Down Protection)

Chimes Include:

- Seatbelt

- Check Engine

- Key In Ignition

- Low Fuel

- Low Oil

- Lights On

Before installing this interface please review the options before

removing the factory radio. Some options may need to be adjusted

prior to removing the factory radio. Options include:

- Standard BOSE Amplifier

- Premium Bose (Y-91)

ONSTAR RADIO REPLACEMENT FOR SELECT GM LAN 29-BIT VEHICLES 2006-UP

SOOGM-16

SOOGM-16A

Harness: 2606 Only.

Covers 2012-UP Pick-Ups

w/ Navigation listed below.

WIRING COLOR CODES

The module has been rated for upto 3A max of output.

For applications demanding a continuous output of 3A or more,

we reccomend using a standard BOSCH (SPDT) relay.

See your local car audio specialist.

OVERVIEW OF INSTALLATION

CONNECT THE WIRES,

COLOR FOR COLOR.

IMPORTANT:

- The Front and Rear fading are not retained on Y-91 BOSE.

- The Onstar volume output is defaulted to low-gain

BUICK:

2008 - 2012 Enclave

2006 - 2011 Lucerne

CADILLAC

2006 - 2010 DTS

2007 - 2013 Escalade

2007 - 2009 SRX

CHEVROLET:

2007 - 2013 Avalanche*

2007 - 2009 Equinox

2008 - 2011 Express Van

2006 - 2013 Impala/ Impala SS

2006 - 2007 Monte Carlo

2007 - 2013 Silverado* 1500-3500 Pickup

2007 - 2013 Suburban*

2007 - 2013 Tahoe*

2009 - 2012 Traverse

GMC:

2007 - 2012 Acadia

2008 - 2011 Savana

2007 - 2013 Sierra 1500-3500 Pickup*

2007 - 2013 Yukon*

HUMMER:

2008 - 2009 H2

PONTIAC:

2007 - 2009 Torrent

SATURN:

2007 - 2009 Outlook

2008 - 2009 Vue

SUZUKI:

2007 - 2008 XL7

*2012 Vehicles with Navigation Units are not

supported. Needed is SOOGM-16A

Tech Tip:

Make sure to wipe the 3.5mm plug

before inserting into the aftermarket radio

to avoid a bad connection.

This Interface Supports:

- BOSE Amplifier

- Y-91 System

- Rear Seat Entertainment*

- Back-Up Camera

USING THE SWC WIRE ON NEW JVC UNITS

New JVC units no longer carry the 3.5mm cable and have added the

SWC signal via a Lt. Blue/Yellow wire.

This wire needs to be connected to the SWC wire labeled “Kenwood”

also Lt. Blue/Yellow. Be sure to keep the dial switch set to number 4

when using JVC units.

Use a small screw

driver to make

adjustments.

Note: Seek Up is not

supported on Jensen

radios.

ADJUSTING THE GAIN

High Gain (Non-Bose Systems)

Press OnStar button, Heear “Onstar Ready“, Turn Dial knob to “9“,

Wait 4 seconds, Press Onstar button “Thank you Good Bye“.

Turn Dial knob back to Aftermarket radio corresponding.

The insterface is defaulted at Low-Gain.(BOSE Systems)

Rev. 082113

REAR SEAT ENTERTAINMENT (SPECIAL ORDER)

1. Conect the rear seat entertainment 16-Pin connector to the vehicles

16-Pin factory connector.

2. Connect the RCA’s to the aftermarket radio video and audio input.

3. Test the video and audio before installing the radio into the dash.

Must Special Order Harness: CJA2333A

CRU

STA

EAD

EEN

GRAY

Connector

Connect to

Ground

BACK-UP CAMERA CONNECTION

1. Conect the back-up camera 16-Pin connector to the vehicles 16-Pin

factory connector.

2. Connect the yellow video RCA to the new aftermarket radio video input.

3. Test the video feed before installing the radio back into the dashboard.

8-PIN

(male plug)

BOSE

Non-BOSE

Part Number:

CJA2103A

INTERFACING SOLUTIONS