Kenwood TS590SG User Manual
4
2 GETTING ACQUAINTED
FRONT PANEL
—— C ——
[METER (DRV)]
Press to switch the meter type {page 12}. Press and
hold to select the Drive output or Antenna output {page
52}.
hold to select the Drive output or Antenna output {page
52}.
[PF B]
You can assign a function to this Programmable
Function key {page 56}.
Function key {page 56}.
[MIC (CAR)]
Press to adjust the microphone gain {page 13}. While
the Speech Processor function is ON, press to adjust
the Speech Processor output level {page 32}. Press
and hold to adjust the carrier level {page 23}.
the Speech Processor function is ON, press to adjust
the Speech Processor output level {page 32}. Press
and hold to adjust the carrier level {page 23}.
[PWR (TX MONI)]
Press to adjust the transmission output power
{pages 13, 58}. Press and hold to turn the
transmission signal monitor function ON or OFF
{page 58}.
{pages 13, 58}. Press and hold to turn the
transmission signal monitor function ON or OFF
{page 58}.
[KEY (DELAY)]
Press to adjust the internal electronic keyer speed
{page 34}. Press and hold to adjust the VOX delay
time for voice mode {page 31} or Break-in time (Full
Break-in/ Semi Break-in time) for CW mode.
{page 34}. Press and hold to adjust the VOX delay
time for voice mode {page 31} or Break-in time (Full
Break-in/ Semi Break-in time) for CW mode.
[GENE]
Press to select the general coverage band memory
{page 11}.
{page 11}.
[1.8 (1)]
Press to select the 1.8 MHz band memory {page 11}
or enter keypad number 1.
or enter keypad number 1.
[3.5 (2)]
Press to select the 3.5 MHz band memory {page 11}
or enter keypad number 2.
or enter keypad number 2.
[7 (3)]
Press to select the 7 MHz band memory {page 11} or
enter keypad number 3.
enter keypad number 3.
[10 (4)]
Press to select the 10 MHz band memory {page 11} or
enter keypad number 4.
enter keypad number 4.
[14 (5)]
Press to select the 14 MHz band memory {page 11} or
enter keypad number 5.
enter keypad number 5.
[18 (6)]
Press to select the 18 MHz band memory {page 11} or
enter keypad number 6.
enter keypad number 6.
—— A ——
[ ]
Press and hold to switch the transceiver power ON
and OFF {page 10}.
and OFF {page 10}.
[PF A]
You can assign a function to this Programmable
Function key {page 56}.
Function key {page 56}.
[ATT (RX ANT)]
Press to turn the receiver attenuator ON or OFF
{page 42}. Press and hold to enable or disable the
RX-ANT terminal {page 52}.
{page 42}. Press and hold to enable or disable the
RX-ANT terminal {page 52}.
[PRE (ANT 1/2)]
Press to turn the pre-amplifi er ON or OFF {page 42}.
Press and hold to select either ANT 1 or ANT 2
{page 52}.
Press and hold to select either ANT 1 or ANT 2
{page 52}.
[VOX (LEV)]
In voice mode, press to turn the VOX (Voice-Operated
Transmit) function ON or OFF {page 31}. In CW
mode, press to turn the Break-in function ON or OFF
{page 34}. Press and hold to adjust the microphone
input gain for VOX operation.
Transmit) function ON or OFF {page 31}. In CW
mode, press to turn the Break-in function ON or OFF
{page 34}. Press and hold to adjust the microphone
input gain for VOX operation.
[PROC (LEV)]
Press to turn the Speech Processor ON or OFF
{page 32}. Press and hold to adjust the Speech
Processor input level.
{page 32}. Press and hold to adjust the Speech
Processor input level.
[SEND]
Press to turn transmission ON or OFF.
[AT (TUNE)]
Press to turn the internal antenna tuner ON or
OFF {page 52}. Press and hold to start tuning the
automatic antenna tuner.
OFF {page 52}. Press and hold to start tuning the
automatic antenna tuner.
—— B ——
PHONES jack
Mate with a 6.3 mm (1/4") diameter, 2-conductor
(mono) or 3-conductor (stereo) plug for connecting a
set of headphones {page 2}.
Mate with a 6.3 mm (1/4") diameter, 2-conductor
(mono) or 3-conductor (stereo) plug for connecting a
set of headphones {page 2}.
MIC connector
Connect a microphone to this connector {page 2}.
Connect a microphone to this connector {page 2}.
A
B
C
D
F
E
G
H